What is the most unpleasant part of reloading for you?

[GB]

I have been reloading for over 50 years and casting bullets, on and off, for over 40 years. This does not make me an expert but does make me experienced. I am a seasoned citizen and as such most of my equipment (reloading/casting equipment) has some age on it. I do not have a progressive loader (my volume of shooting, at this stage of my life, makes it hard to justify the high cost of a good progressive loader.) Anyway, enough about my inherent cheapness.

I was sitting in front of the bench last night, luber-sizing some bullets. (Lyman 450, bought used in the early 70s). As I was thinking, it occurred to me that: Lubing bullets may well be my least favorite part of reloading. But then again, I remember the last time I was trimming cases, I had the same thought. (I use a Wilson trimmer (arguably the best manual trimmer), also bought used in the 60s.) I have made a modification when trimming large quantities of rifle cases so I can use in my drill press but still sort of a PITA.

Except for the fact that I shoot cast bullets in several calibers that are not readily available commercially I would give up casting.(The cost of getting into casting today is almost cost prohibitive. New retail cost on my casting equipment is well over $2500 bucks) I did not get back into casting until my retirement because I could, until recently, buy good commercial cast, in common calibers, for less than I thought my labor was worth. Again except for the semi-weird rifle bullets I like to shoot. As for case trimming, shooting new cases every time, is not a great choice considering my taste in rifle calibers. (.257 Roberts, 250 savage, 264 win mag, ect.) So,I sit at the bench and trim and I sit in front of the bench and lube. Having to pick between my least favorite reloading tasks....... The winner or is it the loser! Lubersizing@*+%&#$

 

[bigggbbruce]

Everything but cost savings.. If only I could teach my dog..

 

[fyimo]

I don't really like the brass resizing stage but it's a part of the process so I do it.

 

[Will2]

Cleaning the brass...

 

[oneounceload]

Everything but cost savings.. If only I could teach my dog..

Or convince my wife............

 

[growr]

There is an unpleasant part to reloading???? Say it ain't so!

MY most unpleasant part is running out of components in the middle of a run...

Randy

 

[austintexas]

I think the thing i least like to do is remove primer pocket crimp from GI brass. I don't do it anymore. I've got enough brass to last. I don't like lubing bullets eather, I got spoiled while stationed at Wheelus AFB. As an E-4 making $165 a month before taxes I was pretty broke. The Rod and gun Club had a complete reloading set up and their bullet luber was a Starr. It was the easiest luber I've ever used. put a bullet in the sizer pull the handle, put in another bullet pull the handle and a lubed bullet fell out the bottom.
SWCA 892

 

[BC38]

I'm not crazy about any part of it - other than being able to shoot twice as much for half the cost.

I don't reload in bulk because I don't shoot competitively. I reload in (fairly) small batches of 200-400 of a given round at a time. So the time saving benefit of a progressive doesn't cost justify for me (IMO)

One day when I retire and have a lot more time and less money, then I may enjoy it more and even get into more detailed load development.

Right now its just part of the hobby in order to be able to shoot 400 or 500 rounds of various ammo per range trip - and not have to feel bad about the expense.

 

[damienph]

I've been reloading since I got out of the Army in 1976, so 41+ years and really enjoy it. I find it to be a real stress reliever. I guess my least favorite is occasionally having to poke pieces of media out of the primer flash holes.

Handloading for me is almost as much fun as handling guns and shooting them. Well, maybe not quite but still enjoyable.

 

[steveno]

my uncle started me at reloading when I was 15 years old (I'm 68 now) and quite frankly reloading ain't much fun at all anymore. I only load for the 41 mag and 45 acp. I bought a box of Sig 45 acp hardball just to keep from reloading

 

[otisrush]

.223 case prep. (Specifically - the length check, trimming, and primer pocket removal.)

The AR enables consumption of ammo that is disproportionate to the effort required to load it up.

Pistol, on the other hand, is more balanced: It's easy to chew through ammo, but it's also easy to get it loaded up.

 

[Ole Joe Clark]

It's case trimming, hands down. I enjoy doing the chores of reloading because I enjoy shooting the results. Back 40 plus years ago I shot a lot more, now if I shoot just a few rounds when I go to the range and watch the wife and daughter shoot well and safely, I have had a good time. I reload when the urge strikes me. I primed a few 9mm the other day because I need to load a some more for them to shoot.

Have a blessed day,

Leon

 

[Ivan the Butcher]

I have been loading since 1978 or 1979. I load 4 gauges of shotgun and about 113 metallic cartridges & 12 and 20 gauge metallic. I enjoy loading in general.

But a long weekend of 4 sons and myself practicing and shooting a 3 day Cowboy shoot, left me with most of 8000 empties! I miss the time to refill them all in about 5 days!

The metallic rounds I shoot a lot I have over 5000 of (45 Colt, 45 ACP and 38 Special) I had 20,000 rounds of 223 reloaded, but the sons got in it a few years ago and I have 3000 now. You can start to see a pattern here!

Ivan

PS. I'll take empty cases & time with the boys, over piles of ammo any day!

 

[Twoboxer]

Least favorite part of reloading? A complete changeover and setup for a run on a progressive press.

I suspect more money is spent minimizing that issue . . . regardless of whether your press is blue or red . . . than any other annoying aspect of reloading. Case feeder, bullet feeder, primer punch, case belling, powder charge. And those stupid primer tubes . . . 2 tubes per 100 rounds. (Yes 2 . . . you load a tube to load a tube.)

Far behind in second place is rifle case prep when trimming is involved.

JMO lol.

 

[joeintexas]

I can't say I really dislike any part of reloading. To me it means I get to spend more time with the kids shooting, our youngest is 31, both boys and girls were brought up shooting and the wife shoots pretty good when we can talk her into going. Being retired now I find reloading is a nice time filler, beats mowing the yard and I'm too old and fat to go sky diving!

 

[gwpercle]

Bending over and picking up the fired brass lying all over the place.
Being the "frugal" (tight ) person I am I just cannot walk off and leave my fired brass...and it ruins my day to come back with any less than I started with. If I come back with more ...that's a great day !
Having aged a bit my back begins to ache before I get them all.
The young don't realize what they have right now....good sound bodies !
Gary

 

[Hang-Fire Hank]

DEVICE WORTH THE $$

GW: Get one of those fairly inexpensive roller cages on a long handle. No more bending over.

Hank M.

 

[Hang-Fire Hank]

I'm exactly with you on both of those onerous chores...trimming bottle neck cases...lube sizing. Trimming is the worst of the two, IMHO.

Hank M.

 

[824tsv]

For me it's being interrupted by someone or something when I'm trying to concentrate on my reloading process. I hate leaving the bench when I'm only part way through the process. Otherwise, I find reloading therapeutic.

 

[lrrifleman]

My least favorite part of reloading is when a case doesn't seat properly on the ram and I snap a depriming pin, or when an occasional Berdan primed case gets into the production line and snaps a depriming pin.