158g Plated bullets for 38?

[Boogsawaste]

Hey all, I have some 158swc from extreme that I've used for 357mag in the past. Been thinking about using them for 38 special now because clean up is easy and well...I already have them!

I normally shoot lead or coated lead in 38 but I'm getting low and decided to look up some loads for these. My latest Speer does not recommend 38's of that weight that are jacketed due to sticking one in the barrel. Extreme's website says to use middle of the road JACKETED data for these.

Other manuals I have have 158 jacketed data available.

I loaded some up with a full load of power pistol (+p max), per the Lyman 49th this weekend. Shot them out of some 357 guns and had nice results. They had some thump but were pleasant in a couple gp100's.

Now I hesitate to down load into normal levels with other powders I have like bullseye, hp38, and unique because of the warning from Speer.

My question is do plated, especially extreme, act like a jacketed as far as resistance down the barrel? I'm assuming so. Is there a real risk of sticking one in the barrel? I have about 500 left and would like to use them for 38's if possible.

Thanks for any help.

 

[cowboy4evr]

Current load data in the manuals will answer your questions as they list both lead and jacketed / plated bullets for the 38 special . Use their load data and you will have no problems . I would not use the minimums posted . I like to start somewhere in the middle . Good Luck , Regards, Paul

 

[Boogsawaste]

Thanks. I was more concerned that Speer pulled their 158 jacketed data and made note of it while the other manufacturers kept theirs.

 

[WR Moore]

Middle of the lead data for a powder generally works well with plated. I'm using 4.5 gr Unique with an OAL of 1.400 with the Berry THP and it clocks with factory.

The plated seem to be more slippery than lead,less than jacketed, but that may vary per coating thickness/alloy as well as core material.

 

[STORMINORMAN]

158gr fmj or plated in 38 S&WSpecial

There are still quite a few fmj (or jhp, jsp, etc.) factory loads available: it is true that many manufacturers may choose to load these in a +P configuration.

But by going to the actual Freedom Munitions site (same company as Xtreme Bullets) you can find valuable info as to how they manufacture (and remanufacture) 158gr ammunition using plated bullets for 38 S&W Specials: you'll find them typically in the 835-900+ fps range.

If you crossreference this to the data on Ballistics 101for fmj, jhp, etc. ammunition you'll see this range as well.

It really doesn't matter which powders you use: the Hodgdon's pistol site has 18 or so loads using the 158gr XTP bullets: these are jacketed bullets. There's also plenty of "wiggle room" because most +P loads start off where standard pressure loads for these end. "MOST"! For example, with WIN231 (or HP38) MIN-MAX for this bullet is 3.8-4.3gr for standard pressure: +P is 4.6gr.

If there is any area where intentionally avoiding the "mouse fart" loads (that some find to be so attractive these days?) makes sense it would be in a case where you have reason to believe that a safety issue may be present.

If this is the case, just start towards the higher end of a published 158gr standard pressure load and enjoy!

 

[rockquarry]

Plated bullets aren't the same as jacketed bullets. I would treat plated as I would any cast bullet and use the same data. As always, however, with any bullet and load data, normal handloading precautions should be practiced.

 

[mikld]

I've only tried about 1,000 plated bullets (for me not any better than my cast) and I used cast bullet data. I'd like to see/hear more about a warning to not use 158 gr bullets, cast, plated, jacketed, solid copper, or PCed, in 38 Special. I have loads many thousands of 38 Special rounds using bullets from 125 gr. to 160 gr, cast, jacketed, PCed, and plated. BTW, I would not load plated to +P levels...

 

[rockquarry]

I tried plated 148 grain WC bullets once in .38 Special. Could see no advantage over my own cast and conventionally lubricated bullets. Accuracy was certainly inferior.

Anyone have good experience with plated bullets in comparison with well made, fitted, cast bullets?

 

[Boogsawaste]

I've only tried about 1,000 plated bullets (for me not any better than my cast) and I used cast bullet data. I'd like to see/hear more about a warning to not use 158 gr bullets, cast, plated, jacketed, solid copper, or PCed, in 38 Special. I have loads many thousands of 38 Special rounds using bullets from 125 gr. to 160 gr, cast, jacketed, PCed, and plated. BTW, I would not load plated to +P levels...

I'll try and remember to take a pic of the wording in my manual tonight. It was only specifically for jacketed and weights above 146 if I remember correctly. I believe it's speer's # 14.

As far as +p, that I don't have any fear of since x treme's own sight says to keep them under 1500fps and anything over 1200 FPS they recommend their heavy plated bullets. I don't think any published load for 158 in 38 special would ever reach that. I've used these in mid range 357 with good results in the past. Kept them in the 1000fps range. I don't need that fast to just punch paper though so that's the reasoning that I would like to shoot them at normal 38spl levels.

Since I don't cast my own (and no plans to start, too many other projects), might as well use these up!

 

[Boogsawaste]

Here are the pages. First 2 are regular pressure 38 special and the 3rd is +p. They even go as far as saying +p pressures aren't a sure enough thing to make sure anything jacketed heavier than 146 grain will exit the barrel.

 

[ontargetagain]

The Xtreme's are not jacketed, they are plated. I used a ton of these in my 6" 686-3 and mostly at lower levels with no issues.
HP38 3.5gr was an accurate load for me, Hodgdon was 3.1-3.8gr recommended cast 158 LSWC.
Karl

 

[TomkinsSP]

IMHO plated bullets are the "sticky-est" the only squib loads I ever created used
low velocity and plated bullets. Plated is it's own animal, not cast, not jacketed.

 

[reddog81]

There's load data out there for 158 grain jacketed bullets. Plated bullets will have less resistance than jacketed. If you're worried about sticking a bullet in the barrel just make sure to pay attention to your target and make sure your bullets are accounted for.

 

[dr. mordo]

I loaded several hundred of the 38 SPL xtreme 158gr plated, but due to the warnings you mention and others I loaded most of them close to max for standard pressure jacketed loads. I had one squib in a 4" M10, which was when I was experimenting with a light-to mid-load of 700x (I'd have to dig out my records to remember for sure).

After that, I stuck to heavier loads and slower powders with plated bullets. I also loaded up some mid power 357s with those plated bullets and had no problems.

 

[TomkinsSP]

There's load data out there for 158 grain jacketed bullets. Plated bullets will have less resistance than jacketed. If you're worried about sticking a bullet in the barrel just make sure to pay attention to your target and make sure your bullets are accounted for.

JMO jacketed bullets are more uniform and of consistent diameter compared to plated. Cast lead is somewhat self lubricating and generally more malleable than either plated or jacketed. I find cast to be most accurate, plated least (but small sample size with plated). Good jacketed (ie Hornady) have given me great results, about as good as good cast (ie Badman), but I have found plated to be least consistant (velocity, accuracy, felt recoil).

 

[BLUEDOT37]

...I would not load plated to +P levels...

.

38 Spcl.(+P) loads max. at 20K PSI. That's not even a good starting load for a 357 Magnum of which many are loaded to higher levels with plated bullets. Just adhere to the manufacturers speed limit for each variation (1250fps, 1500fps, etc.)

.
.

Plated bullets... I would treat plated as I would any cast bullet and use the same data.

Plated bullets will have less resistance than jacketed.

.

There have been several tests (**) done that show plated bullets are the slowest of the bullet types (jacketed, cast lead, coated lead, plated) when comparing the same weight & using the same powder charge. More resistance = slower MV.

Speer pistol bullets are premium plated (chemical electro-plating) bullets.

.

(**)- The referenced website doesn't exist any longer but here's a page with the key data on it that I had saved.

.

.

 

[TomkinsSP]

BlueDot37

This has been my anecdotal experience. Thanks for the empirical evidence.

 

[Protocall_Design]

I have never gotten any decent groups out of Berry's or Ranier plated bullets in a revolver. Different calibers and bullet weights all proved rather dismal compared to excellent groups with cast, polymer coated, and jacketed in the same guns. Never tried Extreme brand.

 

[mikld]

I read the warning and am sure the warning was about light loads and slow powders. Yes, too light a load and there is a possibility of a stuck bullet, but that's with any weight or construction bullet. I have been reloading 38 since '69 (off and on) and using starting loads outta my manual(s) and I have had only one squib, and that was my fault, not the load...

 

[Wise_A]

I believe the specific danger is jacket separation, where the lead core continues downrange, impacting the target, but the jacket remains stuck in the barrel.