Recent content by aslap

Looking for the 46 7” barrel. I have a nice 46 that was bubba’d with scope mounting holes. Long shot, I know. Tony

I have 4 of these (used) and the suppressor thread adapter with the thread cover that I'd like to sell. The bluing is worn on the suppressor adapter. The magazines have been used but are in good working condition. I'd like $90.00 for all and will ship for $10.00 in the continental US. I'll take...

S&W is replacing my faulty full size M&P 22 with the compact piece. I have a Mako rail that attached to the front Picatinny rail on the full size gun that allows me to put attach a red dot. Does anyone know if the front rail on the compact version would also accept the Mako rail adapter? The...

Kudos almost I took the gun to the range today and while the problem appeared fixed while dry firing, it'sdoing the exact same thing that it was doing prior to me sending it out. I'll try again. This has me bummed out now. It is obvious that nobody actually fired the gun after the repair...

I checked in here about a month ago with issues with my M&P22 that appeared to be the sear/hammer engagement. I contacted S&W service and sent it back for repair. They replaced the plunger and I had the gun back in 2 weeks from ship out to return and they gave me and extra 12 round magazine for...

My M&P 22 is an early one with a serial number of 7xxx. I have about 5,000 rounds through it. It has started malfunctioning in that about every other round, after the slide cycles, the gun won't fire and I have to re-cock the gun by re-cycling the slide. Yesterday I had a double fire with it so...

My M&P 22 is an early one (SN 72xx) and has probably 5K rounds through it. It's also been running suppressed for the last couple of years so it has the threaded adapter to mount the suppressor. This has to be removed to clean the gun. There is a shroud around the barrel proper that has a notch...

Thanks!! Thanks for the reply. I'll call the service center tomorrow and get the screws. Tony

I received a 1977 29-2 a few years back as a gift. I've been shooting it ever since with no issues. Mainly reloads that I'd consider to be slightly hot 44 specials - 1100 fps with 240 gr lead bullets. After recently viewing pix of other 29-2's, I saw that the front of my sight assembly was...

I put 200 rounds of each through the gun yesterday and had zero failures to fire with either ammo. The total round count on the gun now is about 600 rounds and consists of RP T-Bolt, CCI Stingers, and Winchester Wildcat. I have three magazines and I did have 4 stovepipes (2 with each brand) that...

I've always wondered.. If really old ammo wouldn't wind up with a much higher pressure spike when shot than new ammo. I could imagine the powder breaking down and possibly leaving more of a volatile content than when new. I'm no chemist (and don't play one on TV) but I could sure see powder...

Sorry. I didn't see the age of this thread. Tony

I got mine a few months ago I think they are available. I bought mine in early January. Magazines are hard to find, though. I was fortunate to find 2 of them a few weeks back. Nice little pistol. I'm planning on shooting it tomorrow and I have maybe 400 rounds through it so far with no big...

All that they said... Polishing the feed ramp is a really good idea. Also, mine had some really bad gunk down in the guts of the action that needed cleared out. I was using Remington T-bolt (bad); Winchester Wildcat ( pretty good); and CCI stingers (very nice). Out of ~300 rounds mixing them...

I don't know about the APEX parts... ...but I picked one up about a month ago and it is a real treat to shoot. I've run really crummy stuff (RP Thunderbolt) and good stuff (CCI Stingers) and all fed and fired. I had several failures of the slide to lock after the last round in the magazine but...