Recent content by Edd Harbin

  1. E

    Range report and update on trigger job and Magazine problem

    Went to the range today and popped off another 250 rounds . Went over the 1k mark ! First I have to address the magazine issue I had with my Shield 9mm . The 7 rnd mag wouldn't lock back all the time . I took the follower out and did a light buff with 1000 grit sandpaper . Now it works perfect ...
  2. E

    Can You Add a mag safety to a M&P

    Yes , the OP got his question aswered .... You can put a fifth wheel on a Corvette . You can also learn proper gun storage , train all people in the household including children ( my 10 year old has better gun handleing skills than most at LGS) . And not buy into gun myth's . The Nannie state...
  3. E

    Can You Add a mag safety to a M&P

    Can you add a fifth wheel to a Corvette ? I'm sure you could but its "like teats on a boar hog " as my father would say . If you want a mag disconect but a gun designed for one .
  4. E

    M&P Shield

    See my post on DIY Over Travel stop . Will fix the low left jerk !
  5. E

    M&P Shield 9 Shooting Way Low Left

    First time out for me I was grouping good , just .... wait for it.... LOW AND LEFT . I knew what was happening , thin , new gun .... I'm puling left and down . Must work on trigger control . I then did a little dry firing (1-2k ) and it got better . I then did alittle trigger work and it got...
  6. E

    DIY Alternative Overtravel stop

    Thanks Spectraman , it's real easy . Right after you place the putty , it is still mallable . I smooth it out and then pull trigger back until contact . I then use that as a template for the face of the travel stop . Then it's just small jewelers files and a little at a time .
  7. E

    DIY Alternative Overtravel stop

    After doing my own trigger job :eek: the only issue with trigger was the amount of overtravel . I decided to try something I've used on other polymer pistols . I took some Marine metal putty and made a physical overtravel for my shield . I started by roughing up the existing overtravel nub...
  8. E

    Legality of aftermarket trigger parts

    1st Gen Sigma was close to 20 lbs ! Worst trigger in the last 25 years .
  9. E

    Problem with 7 round Shield mag lockback .

    Heard from Smith and Wesson , they are sending out a new mag . I have broken the mag down , and I think the problem is the follower . There seems to be some flash , mismolding of the plastic follower . I may try reshaping the follower to see if that helps .
  10. E

    I've been Sticky for 3 days !

    We've been running 95-102 deg for the past week with no end in sight , so I guess I'm extra-sticky :D !
  11. E

    Legality of aftermarket trigger parts

    All she had to do was not put her finger on the trigger and no "Bang,Bang" . She got off easy . The minute you put finger to trigger amd pull , no matter how light , yuo pulled trigger not trigger pulled finger . She and her lawyer were idiot's . Either you meant to pull trigger and it was a...
  12. E

    Legality of aftermarket trigger parts

    This is a "Urban Myth" , only exist in opinion's . And just like ---holes , everyone has one !
  13. E

    I've been Sticky for 3 days !

    I picked up a Sticky holster for my Shield 9mm on Saterday . I wasn't too sure about it but for the price I knew I could use it for a pistol sheath in the car or as a pocket holster if it didn't work out . So far I've used it IWB with jeans , gym shorts with draw string , and even some "around...
  14. E

    Problem with 7 round Shield mag lockback .

    Here is a pic of the slide fully back and the slide stop not engaging .
  15. E

    Problem with 7 round Shield mag lockback .

    Left the 7 rnd mag loaded all night , emptied mag and tried to lock it back .... No joy . It still won't lock back all the time , about 30% of the time . Waiting to hear back from S&W .
See more
Back
Top