Loading 38 Special wad cutters.

H

Hotshot9

Member
Joined
Jan 17, 2016
Messages
225
Reaction score
106
Location
Michigan
Hello folks, I going to load some 38 Special wad cutters for PPC. I'm fairly new to reloading but putting in my time in the books and I have loaded 9 mm. Heres a break down of what I'm going to use for loading, Hornady 38 Special 358 dia. 148 gr. lead hollow base bullets, Remington 1-1/2 primers and either Tite group or Universal powders and brand new brass by Starline So any suggestions and tips ?

Thanks In Advance.
 
Register to hide this ad
Use 2.8 grains bullseye, seat case mouth flush and use a factory taper crimp die.

Forgot to mention, do not try to push the HBWC too hard as you may blow out the skirt. Strive to keep the volocity under 850 fps.

I found for PPC shooting in a K-38, using standard DEWC and seating to the crimp groove proved easier to speed load then HBWC seated flush (unless you are suing a semi-auto wadcutter gun like the model 52.
 
Last edited:
.38 special wad cutters is a good place to start your reloading journey, and one of the easiest rounds to get good results with. I've loaded probably 50,000 rounds of 148 grain wadcutters over the last 40 years but have always stuck with Bullseye, Super Target or my all time favorite, WW 231. Any of the loads from a reputable manual for your powders of choice should start you of right.
 
Given the two powders on the list, I think Universal is a bit slow for HBWC. I would recommend Titegroup, if those 2 powders are the choices. I also use Bullseye - if I can find it, or Reddot (Promo), or even 231.

The thing with HBWC, they like small charges of fast powders, which is one reason they are popular - economy ( read : cheap !) .

Keep the velocity under 850fps to maintain projectile integrity. The HBWC may come apart at higher vels.

Have fun !
 
I know you mentioned wanting to use TG or Universal, but FWIW here is what I like:
148HBWC (Zero) 2.7gr Bullseye FED100 unbelievably soft, but accurate. Also used 2.7gr of WST with excellent results.
 
I also like cast DEWC bullets better than the hollow base WC bullets.

I'm using W231/HP-38 but Bullseye is also very good. You can also use Zip, AA#2, Red Dot and similar speed powders.
 
I load that same Hornady wadcutter with 2.8 grains of Bullseye and get great results. I'm sure that getting equal results with Titegroup will be no problem.
I don't have a taper crimp die for .38 so I just set my roll crimp die to just close the flair of the case. These bullets are sized at .358 so you really shouldn't need much, if any, crimp at all IMO.
 
Just a quick note - since you said you were fairly new to reloading but have done some 9mm, when moving up to larger, straight wall cases such as .38, .357, .44 special, .44 mag and using relatively fast buring powders such as bullseye, 231, red dot take special care when charging the cases.

I know some people will charge a loading block then seat bullets. I also know more than one person has double charged a .38 case and had less than desirable results.

I was trained that you handle only one round at a time. Once the cases have been primed, I will charge a case with powder, then without letting go of the case in my hand, place a bullet on the case and place it in the seating die. Have never had a double charge incident following this procedure. With shorter cases like 9mm, even with 4 grains of bullseye the case is pretty full and a double charge would over flow the case. Not so with the .38.

Good loading
 
I use 3.2 grains of Bullseye pushing a 158 grain plated semi-wadcutter. I suggest you use semi-wadcutters if you're shooting a PPC course, they're much easier to reload into the revolver. Whatever powder you're using, begin with the lightest load recommended for the bullet you're using.
 
Last edited:
Use the Tite group for the light 148gr loadings and
save the slower Universal for when you buy 158gr lead bullets.

There are better and worse powders but those two will work.
If you do get a chance, pick up some bullseye or 231 type powders.
They are the old stand buy's in every loading manual.
 
As a recent convert to WC as a boolit style, I've tried all the powder recipes noted above on 148 DEWC and have great results regardless.

I'd suggest a procedural consideration: only load a small given quantity of each powder or charge weight, say maybe "24" or so clearly marked. Go to range ON PAPER evaluate which gives the best groups from each gun in which you may use them.

Color me surprised, I discovered 2 very similar 4" revolvers, which otherwise seemed to produce very similar results, displayed considerable difference in group size with same recipe.

They both would hit the falling 6" plate rack with few misses, yet on paper one grouped into 4" and the other groups less that 2". Even from the bench I was unable to overcome this anomaly.
 
I realize you are asking about loading WC in this post but for PPC, have you considered using Round Nose bullets? You may find they will load much easier with the speed loaders than wad cutters when using something like Comp 2 or comp 3 cylinder loaders.
 
elpac3 said:
Just a quick note - since you said you were fairly new to reloading but have done some 9mm, when moving up to larger, straight wall cases such as .38, .357, .44 special, .44 mag and using relatively fast buring powders such as bullseye, 231, red dot take special care when charging the cases.


I was trained that you handle only one round at a time. Once the cases have been primed, I will charge a case with powder, then without letting go of the case in my hand, place a bullet on the case and place it in the seating die. Have never had a double charge incident following this procedure. With shorter cases like 9mm, even with 4 grains of bullseye the case is pretty full and a double charge would over flow the case. Not so with the .38.
Click to expand...

That second paragraph is excellent advice.

I used to take a case and hand prime it,then flare it and put it back in the loading block.
Then, take the cases in the loading block, one at a time, put the charge in, and immediately set a projectile on top.

Then it can go back in the loading block, or onto the seating die - however you are set up.

With the small charges in a large case, be extremely vigilant to not over-charge the case.
 
One at a time, all the way through, is much too slow for me. I have done it that way, but just don't care to, these days.

If I'm going to do a hundred or so of 38's, 44's, etc., I'll size them, usually hand prime, and flare them. I just toss them into a tin can. We feed the dogs green beans to supplement their dog food, and have plenty of bean cans.

Then I'll put 50 of them on a loading block, & either load them all with powder, or 15 or 20 at a time in rows. I use the RCBS uniflow powder dispenser with stand, which makes it easy to load the block. I'll then look across the block with a flashlight & my reading glasses. I do not put any bullets on top, at this point.

I grab each one individually, once again noticing the powder charge, and then placing the bullet on top, as I reach to put it in the press. I'll seat all of them, before changing the die, for any crimping, which is done separate from seating.

If I really want to slow down, as well as being too lazy to change primer sizes on my hand primer, I'll place individual primers in the SS press, and press them in in, before the pulling the handle all the way down, for the flare.
 
For the hollow base wadcutter, I like Bullseye or 231 powder, which is a pretty conventional choice.
 
For me I always turn the case upside down and tap it on the table before charging it. I have also placed the cases in the loading block upside down and only charge a case if it is in this position in the block. If a case is right side up in the block, I check and find out why.
 
You must log in or register to reply here.

Similar threads

K
"Neck Turning" 38 Special
2
Replies
31
Views
1K
Just another 22 shooter
Just another 22 shooter
H
38 Special & Vihtavuori Powder
Replies
10
Views
976
BrBa
B
BC38
Loading 7.62x39 Russian
2 3 4
Replies
70
Views
3K
alwslate
A
M
Making 38 special bullets using a 9mm mould.
Replies
6
Views
156
M5741
M
jculloden
38 Super sizer for 38 special brass
Replies
11
Views
751
rosewood
rosewood

Latest posts

Back
Top