FINALLY...A Model 28-2 Smolt Franken Gun

M

Model39

SWCA Member, Absent Comrade
Joined
May 3, 2008
Messages
1,089
Reaction score
3,434
Location
Fairport, New York
After seeing a thread posted by Forum member 410 bore about a Model 28 he found with a 6" Colt Python barrel, I decided that I would also like one. I had seen "K" frame Smith's with Python barrels, but had never seen one on an "N" frame before. The project started when I found a used. not abused, early 6" "S" serial numbered Model 28-2 at a local gun shop. I was lucky to find a 6" ported Colt Python orange ramp front sight barrel on line for a reasonable price, and set things in motion. I sent the cylinder off to TK Custom to be machined for full moon clips and added a .500 target hammer and trigger and a white online blade to the mix. I took the gun and parts to the Custom Shop Gun Shop in Walworth, Wayne County, New York in the fall of 2017. I had asked Dave the owner and master gunsmith to do his magic and build me a two-tone (Army green frame with the rest of the gun in matte black) Smolt Franken Gun. I got a call this afternoon that my gun was ready and when I picked it up I could not have been more happier. This goes to show that good (great) things are worth waiting for.I can't wait to get this to the range. *NOTE* The Birdseye Maple grips which really set this revolver off were made by John Culina. Any thoughts?

 
Register to hide this ad
Congratulation on the new addition to the Family

Even though I do not own one, I have always liked the SMOLTs that I have handled and fired

One of our fellow Forum members from my old neighborhood in Hollywood Florida is a SMOLT fan and owner perhaps he will notice this thread and jump in as well
 
6" 28s are about 44 ounces. Add the ported full lug barrel without the 28's normal taper and recoil must be very light. It would be competitive in local matches that do not allow loading more than 6 cartridges in any gun to attract more competitors by being "revolver friendly."

N frame Smolts are a lot less common than K frame Smolts because the Python's barrel threads have a smaller diameter than N frame barrel threads. Am I correct guessing that weld was added to the barrel threads then the shank was rethreaded?
 
That is pretty darn cool man! Good job.

As to the barrel fitting in the frame, I have wondered how they do that, especially with an N frame.

I would love to do one of these too, except that I would like to make it a pinto in Ford's nickel and Master Blue.
 
Frame Was Sleeved To Accept The Python's Barrel Threads

k22fan said:
6" 28s are about 44 ounces. Add the ported full lug barrel without the 28's normal taper and recoil must be very light. It would be competitive in local matches that do not allow loading more than 6 cartridges in any gun to attract more competitors by being "revolver friendly."

N frame Smolts are a lot less common than K frame Smolts because the Python's barrel threads have a smaller diameter than N frame barrel threads. Am I correct guessing that weld was added to the barrel threads then the shank was rethreaded?
Click to expand...
I believe the frame was sleeved with a threaded piece which screwed into the existing frame threads and then the sleeve was rethreaded to accept the threads of the Colt barrel. A ball detent was fitted into the yoke to lock into the frame since there is no extractor locking pin in the barrel shroud. There was a lot of work done to make this functioned right. It was test fired before finishing to make sure it is range ready. Thank you for your interest.. .
 
Last edited:
Awesome looking gun. I have a friend that has a 472” Mopar Hemi in a 1962 Chevy BelAir. People at car shows scratch their heads. He tells them it’s a secret NASCAR motor that Smokey Yunick was building for GM. So develop a convincing yarn about this Smolt. And have fun shooting it
 
I like almost everything about this frankengun, except those birdseye maple grips. I'm not a fan of combats to begin with, but mainly I just don't like the color. A set of Kurac combats in ebony would look much better IMHO. This gun is begging for some ebony grips. Cool project!
 
I have to disagree with gdogs. My favorite part about that setup is the birdseye maple combat grips. It is a neat looking gun, but I'm not sure if I care too much for the green frame though.
 
I shot a 6 inch 27 in PPC for several years. I always thought the 27/28 6 inch guns needed a heavier barrel for a better balance. The RMs had a heavier barrel than the later made 27/28!

That looks just about right!
 
Nice rig!

Thanks for completing a project that I've long contemplated doing. I've always wanted to do a 4" SMOLT, but wasn't sure what frame to use. I know the traditional SMOLT uses a K frame, but I have a 4" 28-2 that I've been eyeing for such a project.

My main concern was how the barrel rib and top strap will mesh. From a purely aesthetic position, having a step between the barrel and the top strap would drive me nuts; SMOLTS that use a K frame seem to have a much cleaner transition. I am curious as to how an L frame would work in that regard. A 686 and 2.5" or 4" stainless python barrel would be sweet, provided there was no step between the barrel and top strap. I also didn't know about needing to sleeve the frame to accept the smaller barrel shank, wonder if that applies to the L frame as well. hmmm

Thinking my 28-2 will maintain it's factory 4" barrel for now.
 
Good looking wood makes the rest of the guns finish pop. Nice birds eye maple. Looks good. My ccw(carry guns) get pachmeyer grips the range guns have wood grips.
 
Last edited:
Love the Smolts. They were the thing back before the 586.
Can't say anything bad about Culinas, they're one of the two or three at the top of the grip game these days.
The color, though.... sorry, brother, all I can say is, I hope your wife doesn't let you pick out the drapes. :cool:
Enjoy that critter.
 
You must log in or register to reply here.

Similar threads

G
Considering a 28-2 locally.
Replies
0
Views
57
geo57
G
A
Model 28-2 Grips
Replies
4
Views
579
Hawg Rider
H
C
28-2 missing model number
Replies
9
Views
486
weatherby
weatherby
SixgunFife
28-2 With Some Atypical Features
Replies
6
Views
219
SixgunFife
SixgunFife
G
S&W model 28-2 nickel 4"
Replies
11
Views
654
raljr1
R

Latest posts

Back
Top