|
|
08-24-2018, 05:13 AM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: North Texas prairie
Posts: 1,189
Likes: 2,564
Liked 2,111 Times in 665 Posts
|
|
.358 cylinder reamer needed
I have a pair of S&W 64s that have throats measuring .355.
Also: several Rugers with similar dimensions.
Is there a place in North Texas that rents/sells reamers?
_______________________
I don't have Alzheimer's- My wife had me tested.
|
08-24-2018, 08:49 AM
|
|
Member
|
|
|
Join Date: Jan 2007
Location: KY
Posts: 296
Likes: 301
Liked 102 Times in 58 Posts
|
|
Do a search online or maybe on the Ruger forum. Seems like I've read there's an online place that rents what you're looking for.
|
08-24-2018, 09:03 AM
|
Member
|
|
|
Join Date: Jun 2016
Location: for now ,Texas
Posts: 2,741
Likes: 186
Liked 3,300 Times in 1,525 Posts
|
|
You can take a short piece of 5/16" dowel , cut a 1" slit on one end . Get some 320 gr emery cloth from most any auto part store . Cut a piece and roll it onto the dowel , a snug fit into the cylinder throat . Chuck it into a 3/8's drill and slowly ream it larger . It takes time and patience but you can get a very accurate sizing done this way . I recently bought a nickel 19 that had the same problem , under size cylinder throats . When I finished , a 357 pin gauge slid into all 6 cylinder throats , a 358 would not . This is where I wanted to stop . It shoots very accurately -- now . Good Luck , Paul
Last edited by cowboy4evr; 08-24-2018 at 09:05 AM.
|
08-24-2018, 10:52 AM
|
|
Member
|
|
|
Join Date: Nov 2009
Location: New Port Richey, Florida
Posts: 749
Likes: 721
Liked 454 Times in 224 Posts
|
|
.358 Cylinder reamer needed
Try 4D Reamer Rentals - Fred Zeglin at 406-752-2520 and the e-mail is The best chamber reamer rentals and gunsmithing tools from 4D rentals. They rent Chambering reamers, Dakota Bolt Handles and Extensive line of Custom Gunsmithing tools and parts. The reamers are first class and the price for renting is reasonable. Hope this helps.
Nick
__________________
NRA Instructor\GCA Gunsmith
|
The Following 2 Users Like Post:
|
|
08-24-2018, 12:47 PM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,237
Likes: 55,711
Liked 13,761 Times in 4,328 Posts
|
|
If you have a bunch of S&W and Rugers with .355 throats, you may want to check your measuring system. If just using calipers, it would be easy to be off a couple thou.
|
The Following 2 Users Like Post:
|
|
08-24-2018, 12:52 PM
|
Member
|
|
|
Join Date: Sep 2014
Location: IA
Posts: 1,739
Likes: 1,009
Liked 1,635 Times in 806 Posts
|
|
I was thinking along the same lines as Toolguy. I've got a bunch of S&W revolvers and a couple Rugers. None of them have throats that small.
If you decide to proceed I'd guess your best luck will either be a local gunsmith or ordering the parts online
|
08-24-2018, 03:19 PM
|
|
Member
|
|
|
Join Date: Apr 2011
Location: Where this month?
Posts: 3,604
Likes: 264
Liked 4,215 Times in 1,714 Posts
|
|
Quote:
Originally Posted by Toolguy
If you have a bunch of S&W and Rugers with .355 throats, you may want to check your measuring system. If just using calipers, it would be easy to be off a couple thou.
|
Does a 9mm .355 bullet slide through with slight friction or drop through.
|
The Following User Likes This Post:
|
|
08-24-2018, 04:36 PM
|
Member
|
|
|
Join Date: Sep 2014
Location: North Central Ohio
Posts: 921
Likes: 862
Liked 597 Times in 332 Posts
|
|
I too was thinking error in reading. For the same reason I recently purchased a plug gage to check against my calipers.
You can always take the cylinder to a local machine shop, they can accurately measure and verify your throats in question.
Karl
|
08-24-2018, 05:11 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: North Texas prairie
Posts: 1,189
Likes: 2,564
Liked 2,111 Times in 665 Posts
|
|
Trust me, guys, it's not my measuring system.
My two standard measurements are:
Quick 'n dirty- will a (Measured) .358" cast bullet push through and
My trusty pin gauges.
The revolvers with the tight throats are maybe 18% of my total 38/357 accumulation.
_______________________
I don't have Alzheimer's- My wife had me tested.
|
The Following User Likes This Post:
|
|
08-24-2018, 05:52 PM
|
Member
|
|
|
Join Date: Sep 2014
Location: North Central Ohio
Posts: 921
Likes: 862
Liked 597 Times in 332 Posts
|
|
I don't know what is in your local area but Clymer and Manson seem to be the two leading brands to purchase.
Karl
|
08-24-2018, 06:01 PM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Upstate, SC
Posts: 2,063
Likes: 3,165
Liked 4,926 Times in 1,567 Posts
|
|
As far as the potential issue of measuring may seem, in this case it doesn't really matter.
Go ahead and use a .358" reamer. It will only remove material if the throats are undersize. Doesn't matter if they're .355", .356" or even .357". Nothing would be removed if they were .358" or larger.
In fact, if you are casting your own bullets, it might be worth it to throat any .357" cylinders.
But, one caveat..... What are your bore dimensions?
It's best to avoid throating a cylinder to .358" if bore/groove diameter is less than .357", or perhaps .356" at the smallest.
Please post an update with your progress.
Best wishes for success!
Jim
|
The Following User Likes This Post:
|
|
08-24-2018, 10:19 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: North Texas prairie
Posts: 1,189
Likes: 2,564
Liked 2,111 Times in 665 Posts
|
|
Quote:
Originally Posted by 6string
But, one caveat..... What are your bore dimensions?
Jim
|
Jim, I could've sworn that I mentioned that before, but no.
All bores mike out at .3570"/.3576".
_______________________
I don't have Alzheimer's- My wife had me tested.
|
|
Posting Rules
|
|
|
|
|