Search results

I use a target also while use the chrony . I had shot my chrony 2 times and the 2nd time kill it . But the one I got just send in the one and if it can be fix they do otherwise you pay half of the new one. Here is a video for set up with a bore sight https://www.youtube.com/watch?v=3t8fgjgrYLA...

Dose anyone would have the data on a boolit for that weight in 327mag ?

I load for 327 mag and 32 H&R and the rest of the 32's I use the Hornady die set for 32 H&R to 32 S&W . I use the same die for 32 ACP . I got the Lee FCD because of a rifle I had made for 327 was a tight chamber. and it took care of the flare I put on to load cast boolits I make. I load all...

If someone think time is money for reloading do not do it and when things get bad like they did before on how high and hard to ammo do not complain about it. I reload and cast for all center fire I load wheel gun and semi auto and rifle and also shotgun. I also do muzzle loader with side...

I use a Lee tester, That way i get my mix close to what I want and when I melt the alloy from my bullet stop.It will give me more of a idea of what I have to work with because I load for handgun and rifle and some for shotgun.I also made a stand for my Lee glass to read it better.

If you reload a 9mm wheel gun you will not chase brass. I shoot both wheel gun and semi auto.Mainly cast boolits I do myself. like I do all my other center fire ammo.It works for me ,factory ammo is a good start to see how your gun shoots with reloading you can get it shot better then the...

Like stated about the way it was a few years ago when ammo was had to come by ,I did not had any problems with the ammo I reload I did watch how I shot my 22lr ammo .I had end up work on have the centerfire ammo to shoot like a 22lr on most of my rifle because of how it was. So I will keep...

I reload not only for 9mm but other handguns and rifle and also shotgun.It is my hobby and I also cast my own boolits I do not buy them and I use very little jacket. Some of the 357/38 boolits I cast I size down to use in the 9mm. Just like the 32 cals I reload for with cast boolit I size down...

This is what I found in LC brass then regular commercial brass. I had to trim most of the LC brass I bought beside ream out the primer pocket on them.I reload for a Moss. bolt 308 win and a DPMS AR-10 308 and I do not have problems chamber. I use the RCBS small base dies and also do not put...

I do the same thing also.It is too easy to make mistakes with out trying.Why make things worst. I hold off also. It pays off in the end. When I first work on my SW I had a problem at first .But got it taken care of. Then learn to only work on clean my guns when I am rested.

I use primer tubes ,My large tube have a ding in it from years ago . I use a copper wire and put a hook on one end and use that to push the primers down I also use it for the small primer tube also. It dose not have any ding in it but keep some weight on the primers.I done this for years.

I would not use them .428 in the 44 spl/mag cast or lead .For jacket for the 2 you need .429 and for cast .430 or .431 . If the .428 is the right size for you 44-40 pull the bullets and load them for that .Also slug both guns and see what it come to.

I would use just regular loads in my 44 mag RH 7 1/2" It is something when I shoot 310grs Lee cast boolit. It would be shot placement .I rather shoot that round in my marlin it is easyer to handle Like was stated run hot rounds wear gun and case down faster.

I say the same also ,Start low and work up to what the gun tell you.

I use red dot and it dose not matter to me about meters or dirty . It works for me and will keep use it. It is good to hear that the new one did not really change .

When you do not have Dillon ,you do it all on the same die.

I do the same also, when I was have problems I went doing it in the way you stated and took care of the problem

What all he said will work for you.They both have good molds and got some from both.

For how it sounds first need to try some different powders and start at the min and work up to let the gun tell you what it likes. Also as for the .358 bullets some 9mm will work in some others might not ,that is where you need to check what you bore is like others stated.I have one 9mm that it...

I see in your photo that you are use some WC brass and non .There is a differents in the way the brass is made Because of the one with the mark around the brass was made for WC .I put all my aside for when I load for just WC. That brass is getting hard to find at times.