Gun grease or just oil on the slide?

[SoCoRuss]

I see various folks say they use grease on slides and I see the reasons. Is there a concensus on the best types. I see Enos Glide Slide but its appears to need to be +60 degrees for use. The Shooters Choice all weather grease says its a wide range much like CLP so to me it would appear to be better for various temps. Tetras says its a heavy duty grease but says its for wide range of temps? If its heavy duty that seems to be a contridiction.As for Walmarts lithium I would think if you had low temps that could be an issue? I use that on my trailers and truck grease points.

 

[LimaCharlie]

I use Montana X-treme Gun grease. I put a very thin line down the slide rails. It says it is good for -50 to +600 degrees F.

Products « Montana X-Treme

 

[Hock]

I used CLP for all of its purposes until I got tired of having to lube my pistol after 2 weeks of it just sitting in my holster. I used grease on the barrel and rails as those areas see the most friction when the pistol is operating. I use CLP on the rest.

Sent from my BlackBerry Z10 using Tapatalk

 

[N4KVE]

I used CLP for all of its purposes until I got tired of having to lube my pistol after 2 weeks of it just sitting in my holster.

Exactly why I use Tetra grease. When I lube my guns with any modern gun oil, like magic, it's gone in a week, & the gun is dry. Tetra never dries, & like that famous bunny on TV, it always works. GARY

 

[superbeast1098]

Ive used Hoppes Elite gun oil on my SD9VE with good results.... Only thing I didnt like about it is that it tends to dry up after a couple of days...

I started using white litihium grease. I havent fired the gun since I greased it, but just racking the slide, it is a bit smoother and more quiet... lol....

 

[George9]

For a new gun I clean it well inside and out then lube with oil. All moving parts get a little . A new gun does need to break in wear in if you will so wen it comes to lube more is not better less wear is not better at least till your gun is broken in. Also I use a Good gun oil for lube and rust protection . That said if I was shooting 500 or 1000 rounds all the time I may think about using gun grease for things that slide. I guns from 1944 from my dad with no issues at all of any kind to this day with using gun oil. Some guns I did get used and are almost 100 years old. If it's not broke! George

 

[RalphMP9FS]

Thanks for the responses! I decided to follow Smith and Wesson's owners manual and only use oil. The new M&P ran 200 rounds flawlessly at the range yesterday. I cleaned and oiled the M&P a few weeks ago (just one drop at the 7 points), and there was oil lightly oozing out along the rail after the first two clips were fired. I feel oil is more than sufficient at this point in time.

 

[George9]

Also no need to let the oil ooz out oil a rag and wipe the gun down after lubing. All metal parts should be oiled and then wiped down. I use the Same oil rag for years. Your on the right track good going! Be safe and have fun! George

 

[loeman]

In the past I used only gun oil on my (all steel) semis but for several years now I have used a high end automotive grease called Texaco Starplex Moly 2 grease that is lithium based with molybdenum. I use it very sparingly and apply a very thin and even coat of grease on the slide and frame rails of my semi autos after each cleaning. It stays where I put it and it doesn't get gloppy or forced out the back of the guns at the hammer. I can't say it is better or worse than gun specific grease but I sure do love the "feel" when pulling back the slides of my guns. I've used less than one inch of the 9 inch tube so I estimate I have enough for another 50 years or so.

 

[Tex1001]

This is a post that I made on a previous thread concerning using motor oil on firearms. I've used the Mobil 1 lube/grease for 11 years on dozens of guns and both work fantastic. I can fire 150+ rounds in my AR with little crud buildup in the bolt carrier, and that almost wipes off. I use a light film of grease on semi auto rails and it stays in place until I wipe it off to re-apply.

Mix 9 ozs. of Mobil1- 75W90 full synthetic rear end lube mixed with 7 ozs. LSA Mil/spec semi fluid lubricant.
It has great flowing properties, film strength, lubricity, and it flows at -5 degrees F (The lowest my freezer will go). There is VERY little separation over long periods of time. Most PTFE products separate out in a very short time.
For grease I use:
8 ozs. Mobil1 full synthetic gear grease (The red stuff) mixed with 7 ozs. of the same LSA PTFE semi fluid. This makes a light grease that can be used on all sliding parts. It has a great drop temp and adhesive properties.
_______________________
I don't have Alzheimer's- My wife had me tested.

 

[Ira Hynes]

I use Ballistol for all my guns. A light coat on the slide rails and the "turning parts"seems to work great for me. Started using it in the late '60's for black powder rifles. It never failed or froze. I have had a skin reaction to some oils but not this stuff. The only jams I ever had more ammo related than lube problems.

 

[mlapaglia]

Has anyone tried Brian Enos's Slide-Glide?

I use Slide-Glide lite in Denver on all my Sig's and M&P's. Have no problems. I grease the barrel and lock points too. If it pivots it gets oil otherwise it gets grease. Works for me. Also used on my sons Glocks with no problem.

As long as you do something, oil or grease, and do it correctly you should have no problem.

 

[agksimon]

I use Tetra Gun Grease on the rails and where the slide contacts the hammer to reset it and oil the internals of the gun. The one exception is my M&P22, which also gets a very light layer of grease on the barrel, because the slide is aluminum and might wear quickly, if not kept lubed. I wore out a slide on a Walther P-22, because I didn't keep the rails and barrel greased. If you run clean ammo, like CCI Mini-Mags and wipe of the old grease and put new grease on after each shoot of a few hundred rounds, it will never get abrasive.