Model 41 trigger - still adjustable?

[Jim in Idaho]

Looking at this page...


Model 41 maintenance


...shows that there is an adjustment lever which can be moved to change the trigger pull weight on the Model 41, but the example seems to be a few to maybe several years old.

There is nothing on the S&W website to confirm or deny that the new production models still have this same feature, so I was wondering if anyone has a new production model and if it still has that five position adjustment.

Prices on used ones are coming down compared to the last two years, but if they removed that adjustment then it would be hard to pin down exactly when so it would be a roll of the dice on a slightly older one. If they still have that then any 41 in good shape would be a reasonable candidate.

 

[Dave686]

Based on what I got that was supposed to be a Performance Center gun, I would be concerned that S&W had not given a new Model 41 the attention and quality a $1400 gun deserves. I wouldn't be surprised a bit if it was now just another $400 .22 with a $1500 MSRP tag on it. I think I would try to find an older model.

I almost bought one a couple of years ago, but after doing the research I bought a Ruger MARK IV COMPETITION.

 

[RGPM1A]

Looking at this page...


Model 41 maintenance


...shows that there is an adjustment lever which can be moved to change the trigger pull weight on the Model 41, but the example seems to be a few to maybe several years old.

There is nothing on the S&W website to confirm or deny that the new production models still have this same feature, so I was wondering if anyone has a new production model and if it still has that five position adjustment.

Prices on used ones are coming down compared to the last two years, but if they removed that adjustment then it would be hard to pin down exactly when so it would be a roll of the dice on a slightly older one. If they still have that then any 41 in good shape would be a reasonable candidate.

It only takes about 10 seconds to get the slide off the frame. Once off just look in the frame and you will see if the the adjustment block is present.

 

[chief38]

Remove the Slide and look into the pistol right above the trigger. The adjusting piece looks like a saw blade with 5 teeth - a pin locks into one of those teeth setting the pull weight (usually ranges between 2 1/4 - 3 1/4 lbs). If it is there then it is adjustable. I doubt S&W has changed the design but anything is possible. Certainly easy enough to check.

 

[6string]

The M41 trigger really isn't all that adjustable. The idea of it is not much different than the "adjustable" triggers on most hunting rifles. The trigger weight range is nominal at best, relying more on the spring quality than anything. It's only real function is to help get the weight up a bit if you need to pass a pull weight inspection at a big match.
The need for a fully adjustable trigger is a major reason why so many serious target shooters have switched to Pardini, Hämmerli, etc.

The instructions below, and accompanying diagram are for the Hämmerli 208s

Trigger Adjustments
1. Trigger Weight: Increase by turning allen key 1.5mm.
2. Travel: Can be increased by turning clockwise with the combitool, blade #2.
3. Takeup Weight: To access this loosen locking screw on trigger shoe and slide forward. Turn clockwise with allen key 0.9mm to increase.
4. Sear Engagement: Coupling creep between trigger bar and sear can be reduced by turning clockwise with allen key 1.5mm. It is essential that a clearly discernible creep be maintained.

 

[chief38]

The M41 trigger really isn't all that adjustable. The idea of it is not much different than the "adjustable" triggers on most hunting rifles. The trigger weight range is nominal at best, relying more on the spring quality than anything. It's only real function is to help get the weight up a bit if you need to pass a pull weight inspection at a big match.
The need for a fully adjustable trigger is a major reason why so many serious target shooters have switched to Pardini, Hämmerli, etc.

The instructions below, and accompanying diagram are for the Hämmerli 208s

Trigger Adjustments
1. Trigger Weight: Increase by turning allen key 1.5mm.
2. Travel: Can be increased by turning clockwise with the combitool, blade #2.
3. Takeup Weight: To access this loosen locking screw on trigger shoe and slide forward. Turn clockwise with allen key 0.9mm to increase.
4. Sear Engagement: Coupling creep between trigger bar and sear can be reduced by turning clockwise with allen key 1.5mm. It is essential that a clearly discernible creep be maintained.

On my particular M41, the 5 teeth adjust the pull about 1/4 pound each. So mine goes from 2 1/4 - 3 1/4 lbs. While there is no major difference poundage wise (1 pound) it IS percentage wise almost a 50% increase or 33% decrease depending on how you look at it. Mine is set to the lightest pull weight.