boneman
US Veteran
How long do you folks normally tumble your brass? Thank you Larry
tumbling brass?
- Thread starter boneman
- Start date
Register to hide this ad
- Joined
- Dec 17, 2008
- Messages
- 6,623
- Reaction score
- 1,217
media 1- an hour
media2- two hours
works fine for me...i also cut a used dryer sheet into three pieces and put this into each media cycle..pulls a lot of gunk out
media2- two hours
works fine for me...i also cut a used dryer sheet into three pieces and put this into each media cycle..pulls a lot of gunk out
Amici
Member
- Joined
- Nov 22, 2008
- Messages
- 707
- Reaction score
- 8
Until it's sufficiently shiny. Using straight crushed walnut shells with just a touch of media "rejuvenator;" a mild rouge suspension, it takes about 2 hours.
I also use old dryer sheets cut into strips. They do a wonderful job of keeping media clean, extending its working life.
You need to think of it as a crockpot not a microwave. I let mine go 8-12 hours or whatever.
duckloads
Member
My media is old Lyman corn cob treated with car polish. It will clean and polish 45 colt or 38 special cases in a couple of hours. After 4 hours, 460 mag cases still are not real clean. It tough to get the burnt spots off about 1/2 way down from the case mouth. On occasion, I've clean the 460 cases with Never Dull wading polish and then put them in the vibrator for about an hour. That does the trick.
If I wash my brass is 50:50 white vinegar and water with 2tbls salt, soak for 15 minutes and then rinse it almost does not need tumbling. I let it dry in the sun. Tumble for maybe 1-2 hours.
I think some folks neglect the media. It is the cheapest item in reloading and is full of lead and other nasties. Should be change more frequently IMO. I use 50:50 corn and walnut (Lizard bedding)
I think some folks neglect the media. It is the cheapest item in reloading and is full of lead and other nasties. Should be change more frequently IMO. I use 50:50 corn and walnut (Lizard bedding)
If the brass is "dirty" I tumble in rice overnight. If it "needs" shined I use corncob & polish.
Amici
Member
- Joined
- Nov 22, 2008
- Messages
- 707
- Reaction score
- 8
Absolutely. Those who tumble their brass all night are likely wasting electricity or "saving" money by continuing to use worn-out, lead-saturated media.
Neither practice appeals to me.
campfire
Member
I use walnut media and I mix in a good teaspoonful of Brasso then tumble it for about five minutes to make sure it doesn't form lumps. Then I put the brass in the tumbler for about an hour and a half; I have the cleanest brass you could ever wish for.
Campfire
Campfire
acl864
Member
I have a rotary type tumbler which is quieter but takes longer to clean the brass. It was actually designed as a rock tumbler with a small fractional horsepower motor intended to run continuously without maintenance for weeks at a time. I usually start my tumbler last thing before I shut down my shop for the night then let it tumble until I open the shop after supper the next day. Not sure exactly how long it takes to get the brass acceptably clean but 20 or so hours and the brass is sparkling.
It's worth noting that Brasso contains ammonia, which weakens brass over time. There are arguments back and forth about this in all the reloading forums on a regular basis; I tend to the cautious side and don't use it.
Also, a quick google shows that Aussie Brasso has much less ammonia than US-formula, at least according to Wikipedia. (<1% in AU as opposed to 8-10% in US.)
Dan Cash
Member
It is my electricity to use since I pay for it. The brass goes in the tumbler and comes out when it is done or when I remember to take it out. I think my personal record is 8 days at which point my wife turned the tumbler off. She said it was noisy at night. I don't know as I don't hear it.
Amici
Member
- Joined
- Nov 22, 2008
- Messages
- 707
- Reaction score
- 8
A fact which was never in dispute. Whether that use is necessary or efficient was. I stand by my opinion on that subject, just as you are free to hold yours.
CGM
Member
I don't know what clean brass means to different people. But for me, 1/2 hour in my Dillon with pet store corn cob usually does fine. If I want to really go all out...I do 1 hour.
But hey......whatever feels good to anyone is good too!
But hey......whatever feels good to anyone is good too!
oldRoger
US Veteran
I shoot lead. My brass gets smoke, grease, wax, dirt, sand etc on the surface. I, in common with some of you, I wash it first. Usually I put it in the washing machine, hot water, short cycle. I use Simple Green or laundry detergent. I used to add citric acid, but my wife out.
They are damp after the spin cycle, I put them on a screen in the sun to finish drying.
Then into the Thumbler's Tumbler with plain walnut hulls for about 2 hours. Squeaky clean
They are damp after the spin cycle, I put them on a screen in the sun to finish drying.
Then into the Thumbler's Tumbler with plain walnut hulls for about 2 hours. Squeaky clean
arkdweller22
Member
I use walnut and a dab of the Dillon quick polish. Usually 2 hours and the brass is clean.
I stay away from the Brasso for the reasons stated by zercool, especially since the quick polish is ammonia free and does a fine job.
Regards,
Arkdweller
I stay away from the Brasso for the reasons stated by zercool, especially since the quick polish is ammonia free and does a fine job.
Regards,
Arkdweller
campfire
Member
I am very aware of past discussions regarding the use of Brasso and the only reason I am using it is because my brass has a fairly high round count and I don't expect to get much more life from it.
Once they are used up I will be buying a whole new batch of cases and then I will consider using another brand of polish. "But" I can't help thinking that it would be a considerable time before the ammonia in Brasso caused cases to fail.
It would be good if one of our scientific types on this forum could do some testing to lay this argument to rest once and for all.
(My cases are so shiny I have to wear sun glasses to look at them.
Its interesting that Wikapedia says Brasso in Australia has a different ammonia composition to the US, cant for the life of me understand why.
(<1% in AU as opposed to 8-10% in US.)
Campfire
Once they are used up I will be buying a whole new batch of cases and then I will consider using another brand of polish. "But" I can't help thinking that it would be a considerable time before the ammonia in Brasso caused cases to fail.
It would be good if one of our scientific types on this forum could do some testing to lay this argument to rest once and for all.
(My cases are so shiny I have to wear sun glasses to look at them.
Its interesting that Wikapedia says Brasso in Australia has a different ammonia composition to the US, cant for the life of me understand why.
(<1% in AU as opposed to 8-10% in US.)
Campfire
