SWS Brass Deflector is now available

[SimpleWeaponSolutions]

Introducing the Simple Weapon Solutions M&P 15-22 Brass Deflector.

The 15-22 ejects the brass straight out to the right. If you are a left handed shooter, like me, the brass goes straight into your right arm. With the brass deflector most of the brass will drop straight down into a nice pile.

The brass deflector can also be useful to right handed shooters as it will keep the brass from bouncing off lane dividers and landing back onto you, or hitting shooters in the lanes next to you.

The brass deflector is designed to work with most optics that are mounted to the top rail above the ejection port. However with the wide variety of mounting solutions that are available, the brass deflector may not work with your setup.

The Brass Deflector is made from 6061 Aluminum and hard coat anodized black.

The Brass Deflector Kit comes with

• 1 Picatinny Mount
• 1 Shield
• 1 Nylon Tip Set Screw
• 2 Button Head Screws
• 1 1/8 Hex L Key
• 1 3/32 Hex L Key

CURRENT DESIGN IS DISCONTINUED

If you are having issues with the current design please email me at [email protected] so I may be able to contact everyone that is having problems once the new design is up and running.


Current design Brass Deflector Gen 1

 

[Bpregler]

Is it still possible to "open and show clear" during comps?

 

[SimpleWeaponSolutions]

The button head screw closest to the ejection port can be swapped out with a Thumb Head screw to allow the Shield to swing open. I decided not include this option to keep costs down. Thumb head screws can be purchased at your local hardware store.

 

[mk842766]

Thanx!!! Got one....been waitin' on this

 

[SoTX]

Ordered have also been waiting. One of my kids is a lefty this will come in handy

 

[SlingLead]

Looks pretty sweet. Might have to order one.

I think it would be nice to have while shooting outside. Have to pick up brass at local club and would keep the brass in a pretty uniform spot i would think.

Nice Job

 

[Freeway]

Ordered one. Hope I like it!

 

[SimpleWeaponSolutions]

Looks pretty sweet. Might have to order one.

I think it would be nice to have while shooting outside. Have to pick up brass at local club and would keep the brass in a pretty uniform spot i would think.

Nice Job

Most of the brass will drop straight down, but if it is landing on a hard surface such as concrete, then it will bounce around a bit more. It might help with clean up, but I can't say for sure.

Ordered have also been waiting. One of my kids is a lefty this will come in handy

Thanx!!! Got one....been waitin' on this

Ordered one. Hope I like it!

Thanks for the support. If anyone that orders the Brass Deflector does not like it, or it does not fill the roll that they need it to. Let me know and I will give you a full refund.

 

[Scopes]

Hmm, I guess there would be a little trimming of the rail cover to make room for it. Looks factory, nice job.

 

[mwatz]

Just ordered one for me

 

[Bulldogg]

Great idea ordered two

 

[LaCarolus]

Any way you could post some pictures from the front and back of the gun? I am concerned about how far it sticks out from the gun.

 

[Majorlk]

My ghetto deflector has been working just fine these last few months, but this is classier looking, so I just took the plunge.

FWIF, a towel laid on the bench or the ground beside you will stop 95 percent of the bounce, keeping the brass in one pile - most of the time.

 

[Majorlk]

Any way you could post some pictures from the front and back of the gun? I am concerned about how far it sticks out from the gun.

Probably not much further than the brass deflector at the rear of the ejection port. The last two photos shows that pretty well, as do the first two.

My homemade version is that way. Certainly not enough to interfere with anything I have come across.

 

[Claymore_Dude]

I'd buy that just because it looks cool! Forget the part about it deflecting stuff and being a left and what-not!

 

[Jyezahn]

Just ordered mine! Been waiting for this.

 

[RedNeck Jim]

Why not? I'm in.

 

[Maddmax]

The button head screw closest to the ejection port can be swapped out with a Thumb Head screw to allow the Shield to swing open. I decided not include this option to keep costs down. Thumb head screws can be purchased at your local hardware store.

So this (Thunb Head Screw),would also be a good way to clear a stove-pipe or any other issues too?

Also....With a small/medium riser attached,how well "could" it work with a FS Sporting Rifle ?

 

[$ling$hot]

Geez for $30 - you'd think it'd bag it for you too.

I'd like to see some side view pics also. Like how far it sticks out and if there is a bagging option.

Kidding aside. I'm interested in one. I can't tell by the photo if it extrudes out, sits in, or flush w/ the deflector. Could you post a photo from the top - looking down? Just out of curiosity, can you make it in an anodized blue?

 

[SimpleWeaponSolutions]

Any way you could post some pictures from the front and back of the gun? I am concerned about how far it sticks out from the gun.

Geez for $30 - you'd think it'd bag it for you too.

I'd like to see some side view pics also. Like how far it sticks out and if there is a bagging option.

Kidding aside. I'm interested in one. I can't tell by the photo if it extrudes out, sits in, or flush w/ the deflector. Could you post a photo from the top - looking down? Just out of curiosity, can you make it in an anodized blue?

My Brass Deflector sticks out around 1/4 beyond the uppers brass deflector. I will get some pictures up tomorrow morning.

So this (Thunb Head Screw),would also be a good way to clear a stove-pipe or any other issues too?

Also....With a small/medium riser attached,how well "could" it work with a FS Sporting Rifle ?

It is unnecessary to remove the Shield to clear any jams such as a stove pipe. Just roll the rifle over a little and rack the charging handle.

I would not recommend using my Brass Deflector on an AR15. I have not tried it, but I can tell that there will not be enough clearance between the shield and the upper receiver for the larger shell to fully eject.