Firearm and Archery geared Multi-tools.

Beretta Shotgun Tool.

The Beretta shotgun tool is a bit unique in the design department in that its main function is that of a hammer. The sheath is rather well done with the Beretta design on the flap.



Opening the sheath, you can see that there is a side pouch with a rather professional and full sized pin punch. The Beretta Shot gun Tool doesn't pull any punches here.



Yes, that is a very nice pin punch, and with that hammer, I bet you can probably encourage any pin with the gentleness it requires.



You can tell it is from Beretta.



This multi-tool turns into a full sized hammer.



The Beretta Shotgun Tool offers 11 tools for the care and maintenance of your Beretta shotgun. Gunsmith-designed.

·Optima, mobil & victory enhanced choke tool
·Hammer head
·Sheep's foot blade
·2mm punch pin
·Nylon belt sheath
·28-.410 chocke wrench
·12-20 gauge choke wrench
·#2 phillips screwdriver
·Small Pliers
·Flat screwdriver
·Fine File



Summary:

Pro:
- Unique hammer based tool.
- Designed for the folks who like to fiddle with their tools.
- Well finished quality piece of kit.

Cons:
- No 8/32" threading for attachments.
- No locking tools.

NcSTAR Ar-15 Combo Tool.

Meet the brick of the Weapons focused mulit-tool world. The NcSTAR AR-15 Combo Tool isn't pretty, but it does the job.

Here is a photo of the box.



The inside sheath is rather nice, with a side pocket and Velcro flap.



The sheath has a metal belt loop on the back. The side pocket holds a metal wire bore snake in a plastic storage carrier. The AR-15 Combo Tool is located in the main pouch of the sheath.



The tool is of a clam-shell design.



The main tool is a Castle nut wrench for M4 stocks.



With other tools found on both inside covers of the multi-tool.





This tool has the following features:

• M4 Collapsable Stock Castle Nut wrench, A1 and A2 Front Sight Adjustment Tool, A1 Rear Sight Adjustment Tool
• Flat Blade Screw Driver, Lower Receiver Push Pin Tool, Small Drift Pin for Bolt Carrier Cotter Pin
• Bolt Carrier Carbon Scrapper, .223/5.56 Bore Brush, Plastic covered steel Bore Brush Pull Cable
• Broken Shell Extractor





Summary:

Pro:
- Some unique functions you don't see on other multi-tools geared towards the AR platform.
- Sheath is rather nice, and included bore snake is a plus.

Cons:
- Fit and finish a bit lacking. This is a crude tool compared to most others.
- 4 and 5 prong adjustment wrenches are attached...so if you break them, that is it.

Leatherman MUT.

The Leatheman MUT or Military Utility Tool is based on the Skeletool platform. Howerver, where the Skeletool is a medium sized multi-tool, the MUT is big.

The Leatherman MUT comes in a rather nice sheath.





Opening the Velcro flap, you will notice a small front compartment designed to hold the separate scope adjustment wrench. The MUT fits in the large back compartment. There are also side elastics that could possibly hold a flashlight or some other device.



You can clearly see how the MUT looks like a giant Skeletool in shape and design. It even included a pocket clip on one side.





Included are a half serrated blade, a saw, a removable pin punch, and a carbon scraper. Those comprise your fold out tools. Also included is a very ingenious storage solution for longer than average Lelatherman flat style double ended driver bits of which you get 2, and a smaller double ended bit. On top of that, you get a carabiner which doubles as a bottle opener, a hammer on one end along wtih a V notch cutter.



Here is a closeup of the 8/32" threaded male post with the female threaded pin punch.



Here you an see the V notch cutter. When closed, the bit that is installed into the screwdriver dock, acts as a blade protector. You can also see the hammer end, and the carabiner.



Here are the driver bits included with the MUT.



The ingenious bit storage comprises of an plug which you can push from both ends. Center it to block both bits from escaping. Push down to access whichever bit you want.





The pliers feature replaceable carbon steel cutters.



Press down on this piece to unlock the bit from the driver dock.



the MUT comes in 3 flavours. Top is the MUT EOD with included C4 spike. The middle is the MUT BO, and the standard MUT stainless.





The C4 spike on the MUT EOD is replaceable.



There is a very subtle difference from a MUT BO and the MUT EOD. The plastic carrier for the push pin and the C4 spike are different. Otherwise, you could easily attach whichever you want as the threading is the same for both tools.



Summary:

Pro:
- 8/32 male threads and also a pair of female threads on the pliers makes this a nice tool to work with OTIS and other cleaning gun kits.
- Looks like a giant Skeletool.
- Extra long driver bits give you that extra reach.
- Quality sheath and tool.
- V cutter/hammer/carabiner/bottle opener makes that end of the tool feature packed.

Cons:
- The tool verges on complexity.
- Sometimes, the longer bits are difficult to extricate from the tool.

Leatherman Super Tool 300 EOD.

The Leatherman Super Tool 300 EOD is an all black oxide model that features a C4 spike. To accommodate the C4 spike, they had to cut away part of the handle, making the EOD and a regular Super Tool 300 easily identifiable from each other.



Another difference between the Super Tool 300 EOD and a Super Tool 300, the EOD also features a removable saw blade. Of course, it wouldn't be a good EOD tool if it didn't also feature a blasting cap crimper on the pliers.



the C4 spike is replaceable, and is threaded much like that of the MUT. This you can incorporate 8/32" accessories to it if you needed to, providing they are female threaded, as the tool features a male threaded post. I think of the Super Tool 300 EOD as Leathermans version of the older Gerber MP 600 DET.

Summary:

Pro:
- Leatherman quality.
- Pliers feature removable carbon cutters.
- C4 spike is removable and allows for 8/32" female threaded accessories.

Cons:
- I can't think of one.

Leatherman Rail.

Leatherman has come out with a lot of different one piece pocket tools. With the plethora of sports aimed tools, Leatherman also came out with a series of 3 tools geared towards the shooting crowd.

The Rail is designed to maintain the AR weapon platform.



Included with the Rail are 2 medium lenght double ended diver bits, and a pin punch.



The Rail also features the following functions:

Front Sight Adjustment Tool
Replaceable Firearm Disassembly Punch
Carabiner Tool
Oxygen Tank Wrench
1/4” Hex Bit Driver
3/8" Open End Wrench

Summary:

Pro:
- Small and lightweight.
- Feature packed for its size.

Cons:
- The tool is somewhat small and hard to grasp.
- Bits are sometimes difficult to remove from their rubber carrier.
- Pin punch is hard to hold, and it doesn't attach to the Rail pocket multi-tool.
- No 8/32" threading for OTIS accessories.

Leatherman Pump.

The Leatherman Pump is aimed at the shotgun user.



Included are two medium lenght driver bits and a pin punch...all held by a rubber carrier.



The pump features the following functions:

Gut Hook
Choke Tube Wrench
Replaceable Firearm Disassembly Punch
1/4” Hex Bit Driver
1/4" Box Wrench
3/8" Box Wrench
Scope Adjustment Tool
8mm Box Wrench

Summary:

Pro:
- Love that gut hook.
- Choke tube wrench has a nice universal design that is different from the stepped design seen on many other such tools.

Cons:
- The tool is somewhat small and hard to grasp.
- Bits are sometimes difficult to remove from their rubber carrier.
- Pin punch is hard to hold, and it doesn't attach to the Rail pocket multi-tool.
- No 8/32" threading for OTIS accessories.

Leatherman Cam.

The cam's design is focused on the archer.



Included with the tool are 4 double ended driver bits and a broad-head sharpener.



The Cam also features the following function.

Gut Hook
Carabiner Tool
1/4” Hex Bit Driver
Broadhead Wrench

Summary:

Pro:
- Once again, love that gut hook.
- Light and feature packed for its size.

Cons:
- The tool is somewhat small and hard to grasp.
- Bits are sometimes difficult to remove from their rubber carrier.
- Broad-head sharpener is probably the worst designed such tool I have seen. Be very careful with the blades if you decide to use this as a sharpener.

Unknown bow tool with bow square.

I found this one online, and what drew me to this tool was the folding bow square that came with it. It certainly wasn't the multi-tool itself, as this is decidedly on the cheaper end of generic tools of its ilk.



The multi-tool does have spring loaded jaws, a set of small hex wrench, and a somewhat small PE and serrated knives, a small Phillips driver, and combo bottle opener/flat screwdriver.



The pliers do have the capability of setting nocks, which of course is where the bow square comes in.

Summary:

Pro:
- The folding bow square is included.

Cons:
- Cheap as dirt build and construction of the multi-tool.

SOG Powerlock EOD 2.0.

I had forgotten I had this tool. A regular Powerlock with the addition of a C4 spike. Not as good as other EOD efforts by other companies, especially when viewed from the standpoint that no fuse cap crimper is included as a function of the pliers.





A closer look at the C4 spike.



Compound leverage pliers are a SOG specialty.



Yes, being an older version, it has piano hinge locking levers.



Summary:

Pro:
- SOG compound leverage pliers.
- Good quality throughout.

Cons:
- Piano hinge locking levers are a pain to use. They replaced these on the newer versions with a single larger lever.
- No Cap crimper functionality as seen on the Gerber and Leathermans.
- No 8/32 threading to mesh with cleaning kits.

Outdoor Edge Sportsman's Multi-tool.

This is a multi-tool from a company called Outddor Edge. They also produce a Trekker tool for hikers. This is their Sportsman model.

The sheath is of average quality. Nothing fantastic, but very serviceable and should last for a while.



Once you open the sheath, you will come across two sections, the first holds the extensive driver bit kit in its plastic carrier, and the tool itself in the posterior larger compartment.



This tool comes with a few driver bits in a carrier.



The Sportsman model is another archery focused multi-tool as it features a nock set plier function as well as a broadhead wrench.



The pliers are of interest as they are not needle nosed.



Summary:

Pro:
- Heavy and well built.
- Offers the archer a few nice specific features.
- The best designed awl in my opinion.
- Nice V notch cutter.

Cons:
- Fit and finish not the best in class.

Smith and Wesson Universal Armorer Tool.

Here is something a little different. Before we begin, Smith and Wesson tools are made by Taylor Brand LLC. I tend to not have high expectations when it comes to Taylor Brand products, but I guess in this instance, I was pleasantly surprised at the quality. Mind you, it is a rather simple tool to begin with.

The S&W Universal Armorer Tool is basically a very large pen like tool in which both ends unscrew, revealing a set of pin and punches required to work on a variety of weapons. The design eerily looks like a beefed up Multitasker Tube, which I can easily speculate might be the inspiration for this tool.


Apparently, there are two models out there. One is geared towards military and police folks, and features duplicate tools. That one is called model SWMPGT1. That tool has the following tools in duplicates:

1/16" Allen Wrench
1/8" Roll Tip Punch Pin
1/16" Flat Tip Punch Pin
M&P Slave Pin
1/16" Brass Flat Tip Punch Pin

The Universal Armorer Tool carries the model designation SWUAT1, and has the following tools:

1/16" Allen Wrench
1/16" Roll Tip Punch Pin
1/8" Roll Tip Punch Pin
1/16" Flat Tip Punch Pin
1/8" Flat Tip Punch Pin
S&W Slave Pin
1/8" Solid Punch Pin
1/8" Brass Flat Tip Punch Pin
1/8" Brass Roll Tip Punch Pin
1/32" Cut Tip Punch Pin
1/16" Cut Tip Punch Pin
1/8" Cut Tip Punch Pin

I went with the Universal one because I like variety.

The box looks like standard S&W gear.



One end of which carries the model number.



Once opened, there is no doubt that this is a Taylor Brands LLC product.



The MOLLE compliant sheath isn't all that bad. It features the S&W logo on the front flap.



Opening up the sheath, you are greeted with one fat pen looking tool, in a single compartment. The Velcro closure is on a big elastic. Not sure why, but I guess you could probably hang something there, like say, a small hammer, and still be able to close the flap.



And this is the tool.



Both ends unscrew around a center piece. On each end of that center piece is a round rubber piece with holes for the various tools.



S&W logo on one of the end caps and pocket clip.





On the tapered end of the tool, is a hole with a magnet at its base. The various punches and pins slide into the hole and are held in place via that magnet.



A close up of the various punches and tools included.







Summary:

Pro:
- A good assortment of pins and punches.
- Everything is self contained.
- Not bad construction in the aluminum body and threaded areas.
- Inclusion of a pocket clip or belt sheath.

Cons:
- Magnet could be stronger. Some of the pins and punches appear to be not very magnetic to begin with (the gold toned ones).
- Multi-tool dedicated at dis-assembly and assembly of firearms. Lack of pliers.
- Needs other tools to properly use this tool, such as a small mallet.

And that concludes all the multi-tools that I currently have in my collection that are designed to serve either the shooter, hunter, demolition guy, etc. I hope you have enjoyed this serial post, and that you may find it helpful.

I own the Beretta hammer based multi tool. They also made a normal "Leatherman" style tool of the same high quality as the hammer tool, but I saw no reason to buy one as it didn't do anything my 7 or 8 other pocket tool boxes did.

When the US Navy started to reactivate the River Boat Squadrons, a friend of mine was the procurement officer. Every man was outfitted with a Gerber MP600 in the black finish. These are from normal production and have no "Navy Acceptance" markings. The only flaw I found in it, is the replaceable cutting jaw. When cutting a large gauge packing wire I split one jaw and lost the screw. You can get these from Gerber CS but it is a PITA. I was originally disappointed that there was no form of saw, but have found the file to be of great usefulness once I started to use it.

Ivan

In what I think was a brilliant marketing scheme. Remington includes a very nice hard plastic fitted case with their R1 1911's. In the center of the case is a cutout with a brochure for the multitool that belongs in the cut out.

Like a moth to a flame there was no way I could resist the urge to buy the multitool.

It is the only gun related multi tool I own.
http://www.1911r1.com/Products/Accessories/1911-Accessories/1911-Multitool.aspx

Yes, that appears to be the third version of the Pocket Smith...designed and created by Multitasker I would wager.

Ivan the Butcher said:

I own the Beretta hammer based multi tool. They also made a normal "Leatherman" style tool of the same high quality as the hammer tool, but I saw no reason to buy one as it didn't do anything my 7 or 8 other pocket tool boxes did.

When the US Navy started to reactivate the River Boat Squadrons, a friend of mine was the procurement officer. Every man was outfitted with a Gerber MP600 in the black finish. These are from normal production and have no "Navy Acceptance" markings. The only flaw I found in it, is the replaceable cutting jaw. When cutting a large gauge packing wire I split one jaw and lost the screw. You can get these from Gerber CS but it is a PITA. I was originally disappointed that there was no form of saw, but have found the file to be of great usefulness once I started to use it.

Ivan

Click to expand...

I believe the US armed forces were issued the regular Gerber MP600 Black Oxide (BO), or they were not issued but available for personal purchase on bases. Mind you, there are several configurations of the regular BO MP600 models out there. So it does get kind of murky especially as Gerber doesn't give different names to the various MP600 variations out there (Some with saws, others with files, etc...). The ones I have listed here do have different names, because they differ quite a lot from the standard tool sets found on most MP600s.