|
|
05-25-2011, 11:08 AM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Model 625 Performance Center & H.R. 218
Went for my yearly requalification for H.R. 218 (Ret. P.O. CCP through out the US) my 625 for revolver and my Sig 1911 for semi auto. Was using white box Winchester 230 gr, unfortunately 7 rounds failed to fire. 5 in the 625 and 2 in the 1911. The 1911 was not problematic because the magazine always has a couple of spares. However the 625 moon clips don't permit permit easy replacement of an unfired round. Partly my fault in that I failed to carry more than the required 50 rounds in moon clips. So I basically lost 5 shots, luckily I still shot an 82 and passed. If you look closely the unfired rounds appear not to have as deep an indent as the others. I usually fire reloads problem free. Qualification rules mandate factory ammunition. What say you?
|
05-25-2011, 11:51 AM
|
|
SWCA Member Absent Comrade
|
|
|
Join Date: Mar 2002
Location: Vienna, Virginia, USA
Posts: 218
Likes: 38
Liked 135 Times in 31 Posts
|
|
Have the springs been replaced (lightened) in either or both?
|
05-25-2011, 11:55 AM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Yea,
I did go to a Wolff spring in the 625 but not the 1911.
|
05-25-2011, 12:02 PM
|
|
SWCA Member Absent Comrade
|
|
|
Join Date: Mar 2002
Location: Vienna, Virginia, USA
Posts: 218
Likes: 38
Liked 135 Times in 31 Posts
|
|
By chance do you use Federal primers in your re-loads? All my light triggers like Federal primers; there is a substantial difference in primer hardness. Might want to replace the 1911 springs.
|
05-25-2011, 12:06 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Good diagnosis..
Quote:
Originally Posted by Ed45
By chance do you use Federal primers in your re-loads? All my light triggers like Federal primers; there is a substantial difference in primer hardness. Might want to replace the 1911 springs.
|
Yes I do use Federal primers.
|
05-25-2011, 12:09 PM
|
Member
|
|
|
Join Date: Nov 2002
Location: Mesa, Arizona
Posts: 2,556
Likes: 882
Liked 1,719 Times in 549 Posts
|
|
Ed, the OP said he was using WW white box.
I've heard any number of reports of WW white box 45 ACP causing problems. That's a lot of mis-fires, particularly in a 1911 style firearm. Pick better factory ammo the next time.
When I did my LEOSA qualification in December I shot the auto part with the Glock that rattles around in the truck and the revolver part with a 1937 38/44 HD. What a hoot!
Dave
__________________
RSVN '69-'71
PCSD (Ret)
|
05-25-2011, 12:58 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Thanks Dave
Quote:
Originally Posted by Dave T
Ed, the OP said he was using WW white box.
I've heard any number of reports of WW white box 45 ACP causing problems. That's a lot of mis-fires, particularly in a 1911 style firearm. Pick better factory ammo the next time.
When I did my LEOSA qualification in December I shot the auto part with the Glock that rattles around in the truck and the revolver part with a 1937 38/44 HD. What a hoot!
Dave
|
I'll definitely use other ammo next time.
|
05-25-2011, 01:11 PM
|
|
Member
|
|
|
Join Date: Oct 2010
Posts: 7,202
Likes: 9,079
Liked 1,921 Times in 1,043 Posts
|
|
I have never used WWB in my 625-3 but have used it for years before reloading in my 1911’s. I never had a problem with it. It’s good to know either quality has taken a dive or I was just that lucky. Anyone want to share what factory ammo they would take to something important like a qualification?
|
05-25-2011, 03:38 PM
|
Member
|
|
|
Join Date: Aug 2004
Location: Roebling, NJ, USA
Posts: 718
Likes: 9
Liked 283 Times in 87 Posts
|
|
In recent years, I have seen all kinds of problems with WWB .45 ammo. Light primer strikes, underpowered loads, etc. I switched to Federal AE, which works flawlessly in both autos and revolvers.
|
05-25-2011, 10:02 PM
|
Member
|
|
|
Join Date: Nov 2009
Location: Maryland
Posts: 13
Likes: 0
Liked 5 Times in 4 Posts
|
|
Carl3989, for your 625, try replacing the stock firing pin with a longer after market one. I had some problems with my 625 using my reloads assembled with the harder CCI primers.
I installed an Apex Tactical XP Ignition Kit https://apextactical.com/store/produ....php?pid4.html. Solved that problem.
|
05-25-2011, 10:06 PM
|
Member
|
|
|
Join Date: Dec 2009
Location: Georgia
Posts: 858
Likes: 14
Liked 82 Times in 52 Posts
|
|
I went for my LEOSA qual in April.
I take two revolvers and two semi's.....plus extra ammo.
You never know.
|
05-26-2011, 10:25 AM
|
Member
|
|
|
Join Date: Feb 2007
Posts: 2,100
Likes: 0
Liked 389 Times in 225 Posts
|
|
I use a lot of Winchester primers when loading .45 ACP for my three 625s and two Glock 21s. I presume that they factory load the same primers they sell as components. Or are they different? I never have any problems with their primers. My guess is that your springs are too light.
Dave Sinko
|
05-26-2011, 10:49 AM
|
Member
|
|
|
Join Date: Mar 2009
Location: mid Missouri
Posts: 1,871
Likes: 9,407
Liked 2,560 Times in 1,010 Posts
|
|
the only problem I've ever had with WW primers
is that our Dillon 550 reloader doesn't like em nearly as much as it does CCI's. The WW's seem to be a little out of round or oversized sometimes. Did you put a lighter mainspring in your 1911? In this months issue of the American Rifleman, there is an exc article on dealing with the problems of a 1911. Got our issue this week.
|
05-26-2011, 11:45 AM
|
Member
|
|
|
Join Date: Sep 2007
Location: Southwestern Ohio
Posts: 2,337
Likes: 209
Liked 1,195 Times in 457 Posts
|
|
Carl3989;
Primers that do not fire nearly always show "light strikes". Fired primers back out of the cases, then pressure shoves the cases back, shoving the primers flush. That action causes deeper firing pin indentations in the fired cases. THAT is normal.
However, I would first check the main spring strain screw just to be sure. It should be tightened firmly.
Since you had misfires in your 1911, also, I suggest it is an ammo problem. I would suggest Federal factory for your qualification as Federal primers are known to be softer (they are my chosen brand for everyday use as well as self defense ammo).
You have learned two lessons with your near misfortune. Always fire enough of the chosen ammo to be certain it is compatible with your guns. Second, ALWAYS take extra ammunition.
I am also a fan of Apex Tactical's "extra length" firing pins. They are my choice for my two 625's as well as my daily carry 642 and my Performance Center 629 Light Hunter (which was plagued by misfires until I replaced the springs and firing pin).
As something else to consider - I am NOT a fan of "too light" actions on Smith revolvers. I use Jerry Miculek's spring kits (Bang.com) but set the double action at 9.0 lbs and single action at 3.0 pounds for sure strike on any major company primer, including Winchester's. I use a Lyman trigger pull gauge (electronic) to check both single and double action when setting them up. This is considerably lighter than factory issue but works with most anything I run through the revolvers.
A thought or two...
Dale53
|
05-26-2011, 12:32 PM
|
Member
|
|
|
Join Date: Nov 2010
Location: North Carolina
Posts: 226
Likes: 0
Liked 9 Times in 4 Posts
|
|
I'd at least call Winchester and give them a complaint. Misfires could be dangerous to the new shooters out there. Be sure to give them the lot number if you kept the box.
|
05-26-2011, 03:54 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Interesting
Quote:
Originally Posted by MifflinKid
Carl3989, for your 625, try replacing the stock firing pin with a longer after market one. I had some problems with my 625 using my reloads assembled with the harder CCI primers.
I installed an Apex Tactical XP Ignition Kit https://apextactical.com/store/produ....php?pid4.html. Solved that problem.
|
I have dvds by Jerry Miculak showing S&W revolver disassembly. Unfortunately they cover the external firing pins. Could you suggest where I could learn about the internal firing pin?
|
05-26-2011, 06:20 PM
|
US Veteran Absent Comrade
|
|
|
Join Date: Jan 2010
Location: San Diego, PRK
Posts: 9,237
Likes: 11,531
Liked 11,249 Times in 3,916 Posts
|
|
Quote:
Originally Posted by Dave T
I've heard any number of reports of WW white box 45 ACP causing problems. That's a lot of mis-fires, particularly in a 1911 style firearm. Pick better factory ammo the next time.
Dave
|
They've been having problems lately. They're moving their operations & I understand the Union's not happy about it.
If it was just the 625 I'd say the primers look exactly like my friend's did when the strain screw backed out of his light springed 629.
But two guns? Gotsta be the ammo.
|
05-26-2011, 06:54 PM
|
|
Member
|
|
|
Join Date: Oct 2003
Location: Western New York
Posts: 469
Likes: 56
Liked 18 Times in 13 Posts
|
|
Just apply for your pistol permit and be done with this B.S.
|
05-26-2011, 07:07 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Huh?
Quote:
Originally Posted by Gun-runner
Just apply for your pistol permit and be done with this B.S.
|
What are you referring to, please illuminate me.
|
05-27-2011, 05:10 AM
|
SWCA Member Absent Comrade
|
|
|
Join Date: Nov 2002
Location: SLC, Utah
Posts: 5,060
Likes: 739
Liked 3,276 Times in 1,282 Posts
|
|
I will second the red box Federal American Eagle ammo. My department shoots it for training ammo in 9mm, .40, .45 and it is extremely consistent and reliable. Around here it is priced similarly to Winchester white box.
|
05-27-2011, 09:46 AM
|
Member
|
|
|
Join Date: Feb 2007
Posts: 2,100
Likes: 0
Liked 389 Times in 225 Posts
|
|
Your new 625 will disassemble the same way as an old one. The frame mounted firing pin and spring are held in place by a pin that is easily removed. Disassemble slowly so that you do not lose any parts and it is easy to see how the firing pin is held in the frame.
I have owned two revolvers with frame mounted firing pins. Both were absolutely reliable with all primers as they came from the factory. Actually both were over-sprung and would still fire all primers even when spring tension was slightly reduced. Install completely stock components and go from there. You will need to eliminate all firearm variables before you begin to blame the ammo. Making the gun completely stock and using the "bad" ammo seems the most logical way to proceed. That you just might happen to have a defective or compromised 1911 as well doesn't surprise me one bit.
Dave Sinko
|
05-27-2011, 04:36 PM
|
Member
|
|
|
Join Date: Nov 2009
Location: Maryland
Posts: 13
Likes: 0
Liked 5 Times in 4 Posts
|
|
Quote:
I have dvds by Jerry Miculak showing S&W revolver disassembly. Unfortunately they cover the external firing pins. Could you suggest where I could learn about the internal firing pin?
Reply With Quote
|
David Sinko answered that one. If you understand Jerry's DVD and you have a proper set of screwdriver tips you'll be fine. I used a small needle nose plier to pull the pin that retains the firing pin. Just don't let the factory firing pin get away from you as it is lightly spring loaded.
I polished the Apex Tactical XP firing pin using some Mother's Mag and Aluminum Polish before installing it. Also, while the firing pin was out of the frame I took a small drill bit and ran it through the firing pin bushing hole to remove any burrs. I just twirled it with thumb and finger.
I've read that S&W now puts slightly shorter firing pins in their guns to help them pass some state-level drop safety tests. I have replaced all of my newer S&W internal firing pins with the Apex Tactical XP firing pin and springs. As I recall the AT XP firing pins are about .005" to .006" longer than the stock firing pins. I doesn't seem like much but it does the trick.
Oh yeah, the AT XP spring is made of thiner wire so that probably allows the firing pin to move farther and faster, improving ignition.
|
05-27-2011, 09:00 PM
|
|
Member
|
|
|
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
|
|
Thanks Guys.
Quote:
Originally Posted by MifflinKid
David Sinko answered that one. If you understand Jerry's DVD and you have a proper set of screwdriver tips you'll be fine. I used a small needle nose plier to pull the pin that retains the firing pin. Just don't let the factory firing pin get away from you as it is lightly spring loaded.
I polished the Apex Tactical XP firing pin using some Mother's Mag and Aluminum Polish before installing it. Also, while the firing pin was out of the frame I took a small drill bit and ran it through the firing pin bushing hole to remove any burrs. I just twirled it with thumb and finger.
I've read that S&W now puts slightly shorter firing pins in their guns to help them pass some state-level drop safety tests. I have replaced all of my newer S&W internal firing pins with the Apex Tactical XP firing pin and springs. As I recall the AT XP firing pins are about .005" to .006" longer than the stock firing pins. I doesn't seem like much but it does the trick.
Oh yeah, the AT XP spring is made of thiner wire so that probably allows the firing pin to move farther and faster, improving ignition.
|
I'll have to give that a try.
|
|
Tags
|
1911, 629, 642, glock, model 625, performance center, primer, rifleman, screwdriver, sig arms, tactical, winchester |
Posting Rules
|
|
|
|
|