Model 79 Disassembly

gunner12 · Dec 21, 2012

Several months ago I found S & W Model 79 Co2 air pistol. I sat it aside and thought "I'll fix this someday". It will leak all the Co2 out of a cannister in about three minutes. Well, now I need to have my knee joints replaced, one at a time of course. Since I will be imobilized for quite a while I thought I would refurbish the #79 and use it for indoor target practice while my movement is limited. I am 70+ and have worked on guns for most of my life, however I have not figured out how to disassemble the #79. Replacing O-rings and seals does not seem like a major chore, if I can get to them without destroying the gun in the process. Anyone got any information on disassembling a Model 79?
Thanks in Advance for any/all help. Regards, Gunner12

dfariswheel · Dec 21, 2012

Here's an owner's manual that has a schematic:

http://stevespages.com/pdf/s&w_78g_79g_air_pistol.pdf

Sorry, it's been so many years since I had one apart I just can't remember how.

Here's some info that will help:

Another Airgun Blog: Smith and Wesson Model 79G Disassembly, Part 1

And, a couple of posts down are links to more:

Airgun forum: How do I take apart a S&W 78G/79?

Gun Parts Corp still sell some parts for them:

SMITH & WESSON Accessories | Numrich Gun Parts

gunner12 · Dec 26, 2012

Thanks a million guys. The advice permitted me to complete the disassembly without damaging the gun and also to find two sources for O-rings/seals (now on order). I was sure frustrated until I happened upon this site and got the info from all of you. Perhaps I can return the favor some day. Hope your Christmas was good and that your New Years is bright. Regards, Gunner12

SOLAVAIN · Dec 14, 2013

S&W 79G no gas

Hi,

I change all ring seals everything is OK tench nothing leaks, but the gas does not happen again in the compression chamber.

I do not understand anything.

Do you know this problem?

Thank you for your answer.

Best regards.

JCs Shooting club Girondins de Bordeaux FRANCE

dfariswheel · Dec 14, 2013

Without actually seeing the gun it's impossible to diagnose a problem like this.

If the gun is assembled properly and holding Co2, but not firing, I'd look at the valves to see if one is stuck or clogged.

You can still buy many Model 79 parts from Gun Parts Corporation.

SMITH & WESSON Accessories | Numrich Gun Parts

In France, you should be able to find a gunsmith who specializes in air guns, and he should be able to find the problem.

Good luck.

SOLAVAIN · Dec 15, 2013

S&W 79G waiting

Hi,
yes I understand that I can add.
OK cartridge is properly struck,
OK Home chamber cartridge is pressurized
OK gun is waterproof
OK assembly and reassembly redone order and meaning of pieces verifies.
OK The work make et remake by two people.
OK no visible leads botched.

but One has the impression that the opening system is not powerful enough to open the gas arrives in the compression chamber.

Best regards.

JCs Shooting club Girondins de Bordeaux from FRANCE

Bests regards. JCs

dfariswheel · Dec 15, 2013

Read the owner's manual.
It shows how to adjust the gas system.
Possibly it needs to be adjusted, or the hammer spring is worn.
The hammer spring also regulates the amount of gas released. If the spring is weak, the hammer won't hit the valve hard enough to release gas.

http://stevespages.com/pdf/s&w_78g_79g_air_pistol.pdf

Jjquinn · Sep 7, 2015

smith and wesson model 78g air pistol disassembly

Need help getting the top off the smith and wesson model 78g air pistol. Can any one help. Willing to pay to ship to and pay for the repair

Model 79 Disassembly

gunner12

Member

dfariswheel

Member

gunner12

Member

SOLAVAIN

dfariswheel

Member

SOLAVAIN

dfariswheel

Member

Jjquinn

Similar threads

Latest posts