Search results

M&P 1.0 .357 sig compact, tru glow sites, crimson grip, apex trigger workx, wolf springs, stout but safe loading of longshot powder xtp 124g missles. 1405 fps avg. ring the steel at 100yrds all day.

hurts just to look at that disaster. 30 yrs of tid bits tucked in what a shame. been there done that. on the bright side the upgrades and reorg ideas now have a starting point. words of wisdom to share. when you scoop up the heaps and try to separate them take your time. later recheck the...

RPG, thanks for the reply. I will say there is merit to most of your statements. I agree that no bullet or sight change will correct this piece as it's an obvious machining error. it's now boxed and on it's way back to the birthplace for some "tuning".

finally had a chance to fire my new bodyguard .380 bug. put 40 rds. of wwb and 10rds. of corbon 90g through it without a hitch. really want to like this punch and pull little guy. two concerns stood right out: 1) it shoots two 1/2 foot low at 20 ft. poa was dead center horizontal. two 1/2 foot...

double fat finger post :):p:o:(:rolleyes:;):D

love my M&P357c. when we are one, the bad guys done! ain't no more spendy than a box of 40's or 45's. i reload and costs me less than a box of cheap 9mm. bit of reading for you's that are interested in the .357 sig. CALIBERS -- 357SIG Advocacy Best Choices for Self Defense Ammo

not my picture. but i also have done this to my don hume 715. fits my M&P357c with crimson trace like a glove. i also have a galco n3. both are comfortable and adjust position easly for various activities.

i own both of the pistols in question. i shopped around and fired quite a few rentals before i bought the sr9c last june. i then bought the M&P357c a week later. they are both fine weapons. both are nearing the 2,000 round mark. neither have had any problems that needed attention. the trigger on...

i also just purchased my first ever laser, a ctc grip for my mp357c. all i can say after the first run on the range is, WOW!

i could use some .357 sig if you have any?

alot of good advice here. you didn't mention if these were rentals or a friends guns. one of the big offences i see with range rentals is, their feed large amounts of cheap ammo and rarely cleaned (if you want to call it that) till there is a problem. you'll have a hard time hitting with a...

the start of this post was the concern of primer flatting/hatting with low velocities with a starting load of powder. now i find that i do have a headspace concern. how much of a effect the head space has on the primer problem i don't know? anyone have an actual published s&w spec.?

when i was digging around for some spec's. i can across this site page. pretty good basic smith info. how good the specs are i don't know. i didn't come across any printed smith data. http://www.ammoland.com/2008/12/04/inspection-guide-for-smith-and-wesson-revolvers/ copied over: Headspace...

i managed to get a shot of the forcing cone that is clear enough to see. i also measured some of the clearances with feeler gauges. b/c .007 endshake .0035 head space .016 firing pin .029 cylinder stop has some slop. i cannot see any peening in the cylinder recesses. i did not have a chance...

wanta trade?.................:D never happen.

(bold) thats what concerns me about hornady's xtp data. they tend to use quite a few more grains than most other data i find published. all while using the same col's and such. not for just this caliber several others. interesting, i'll have to look into this somemore. i was playing around...

you guys are great. learning much from all this info. i'm also a fan of big slow moving projectials. be it bullets or arrows, heavy gets the job done no question. this pistol is no queen. it's taken 5 deer using winchester ammo. they have all been one shot harvests, i do pick my shots. my...

lots of good info offered guys thanks. i think i will pull a few factory rounds and put my powder and bullet in to see what they look like. what is your feeling that the fine h110 powder is working its way into the flash hole an creating the problem? it was mentioned to me that i may have a...

i posted this on another site. not getting the attention i was hoping for. should have just came here to the S&W forum to start with...... what was i thinking? i just returned from the range and testing my loadings for my S&W 29-2 for deer hunting. not really seeing what i should have for...

thanks guys. nice to know the d.o.b. :)