Built a bench...

[lhump1961]

Well the OP original post was in 09/25/12 you want to bet it is now cluttered? Don

Since you folks were nice enough to resurrect this thread I'll throw in an update. Cluttered and out of space? Oh, yeah! That happened quick so I have had to expand since those pics were taken...a lot! I have to admit I tidied up a bit for these updates as I usually have something in progress.

I've been very satisfied with my hand loads and get great pleasure from the process...I think my stuff is better than factory! I don't usually load to the top end of specs but rather prefer stuff that suits me. I can load .357's for my K frames right where they should be while my L frames might be something a bit different. The 380's, 9's, 40's and 45's are pretty straight forward so the .357sig for the M&Pc is a nice distraction. My dad is still very active and loads most of the long guns but I did take over for my Marlin 30-30...my gun...my loads. Started shooting trap with my son-in-law so there's that, too...loading trap is quick and easy so no big deal, the MEC is always ready to crank out some AA's for the Citori!

Thanks for the comments and feel free to share any suggestions.

 

[Rule3]

Your killing me here! Still to neat

Envy of all that room.

 

[X Ring]

Still looks neat and organized to me, I like.

 

[Magload]

I can see you have taken over the whole room. Good move. Don

 

[Bigdog357]

Nice setup, really like your original bench with the sliding doors. I designed and built mine based on my needs, seems like I never have enough room.

 

[lhump1961]

Nice setup, really like your original bench with the sliding doors. I designed and built mine based on my needs, seems like I never have enough room.

I like your set up better...more thought out. Mine has been added to but it's in need of a re-think to accommodate the stuff as a whole. I need to go around the corner with bench as you've done. Very nice.

 

[2011redrider]

Nice looking Bench! Built same one back in the late 70's. Was recently getting ready to build a new bench and came across the plans on the internet. Remember building it with my Dad who has passed on. Great memories! Was very sturdy and had lots of storage.

Great Job!

PS here is the link to the plans if anyone wants to build it, even comes with a layout and cutting diagram.
https://www.shotgunsportsmagazine.com/downloads/bench_plans.pdf

 

[Nevada Ed]

Nice bench but...............

you have W231 !!

Holly molly.............

 

[S&WIowegan]

I built the very same bench over 20 yrs ago. It was the plans from the Reloading Manufacturers trade organization and cost $5 mailed to me. It is heavy and bull strong. The thing is so sturdy it NEVER wiggles when running my Dillon 650 presses. I built it after struggling with benches that seemed strong but wobbled constantly when loading. I load standing up because I get less pain and kinks and the plans leg length was perfect for stand-up.

Highly recommended!

 

[lhump1961]

I built the very same bench over 20 yrs ago. It was the plans from the Reloading Manufacturers trade organization and cost $5 mailed to me. It is heavy and bull strong. The thing is so sturdy it NEVER wiggles when running my Dillon 650 presses. I built it after struggling with benches that seemed strong but wobbled constantly when loading. I load standing up because I get less pain and kinks and the plans leg length was perfect for stand-up.

Highly recommended!

I also load standing up and adjusted the leg length (couple of inches) to suit my height. I pushed the top section back two inches to give it a bit more working depth and laminated the surface for good visibility and easy clean up. With over 400 lbs of lead on the lower shelf it doesn't move at all...not a bit!

This bench plan has been around a long time and is tough to improve upon.