Model 64's?

[SFsc616171]

Hi folks!

I've been writing my 'inner checklist', as I've been visiting the 'firearms-brokers-America dot coms', looking at the S and W Model 64, pencil barrels in stainless steel. The only '64s' I know, are the Heavy Barrel models.

QUESTION: what is the known history of these revolvers, and are they 'safe to touch', or if acquired, become shining examples of 'hangar queens', i.e., all show, but do NOT go?

I bought that M15, that is yet displayed on 'gunsAmerica', the one with the teflon dip and Hogue combat grips. I, also, own a Taurus M82. I know, no comparison, and I did NOT know that too well, until I shot both! I've really been SW-bit!

Thanks!

 

[murphydog]

The original model 64s had 4" tapered barrels and were made from 1970-'73. They are good shooters (think of how many police had tapered barrel 4" model 10s, then translate into stainless) and more collectible as time goes on.

 

[Norton 750]

To me, the pencil barrels balance better. I really like the round butt models with four inch BBL's but they are harder to find.

 

[stuart9534]

I actually prefer the heavy barrels. The pencil barreled models are just beautiful to me.

 

[jpwhel]

I have had the standard (tapered) barrel Mod 10 4" barrel for many years and really like the classic looks of the gun. Recently I saw a Mod 64 with the tapered 4" barrel, no box or papers made in 1973, on one of the auction sites. I picked it up for $265. It is a little rough in a few places but I think I can polish it where it looks like new. It will be a nice companion for my Mod 10.

For the OP these are not safe hangar queens, the S&W guns are meant to be shot and enjoyed.

 

[deanodog]

I love the 64 standard barrels. I don't have one but I am looking. I would like to see some pictures if anyone has some to show.

 

[Prefixingto]

I just picked one up for 150 bucks and polished it up! It turned out really nice. Put a hogue grip on it for 15 dollars.

 

[Timbo22]

I have three model 64s; two no dash tapered barrels and one dash 3 three inch heavy barrel. All were purchased used without boxes and papers so all to go to the range. The two tapered barrel models have minor differences in the roll markings so they are not exactly twins, but close siblings. The little differences make them fun and interesting to me. If you can find a model 64 for a reasonable price, pick it up. You can't go wrong.

 

[Richard Simmons]

Not much I can add to what's already been posted about the standard barrel Model 64 except that I sure like mine!

Noah Zark has a beautiful trio of these that's he's posted photos of in the past and in fact he's the reason I have mine today. Thanks again for that Noah!

 

[bigun]

Here are a few pictures of the 2" standard barell model 64(No dash #)revolver that I'd found about two years ago! I've yet to run across another one of these!:

 

[mag318]

The 64 no dash is a classic now. To me the pencil barreled examples have perfect balance. The M&P (Model 10) was S&Ws bread and butter revolver. Making them in stainless steel made a great gun even better.

 

[bigun]

The 64 no dash is a classic now. To me the pencil barreled examples have perfect balance. The M&P (Model 10) was S&Ws bread and butter revolver. Making them in stainless steel made a great gun even better.

Your 64 no dash pencul barrel is music to my eyes! That one is next on my list! Just beautiful!

 

[roundgunner]

I got this 3" for my daughter. I worked the action over on this a bit, now it is so smooth I may just have to keep it and get her something "newer"

 

[stantheman86]

For shooting I vastly prefer the 4" HB 64's and 10's. The 64's are great, no worries with wearing the blue finish with holster wear or use.

The taper barrels look great, but the HB 4" RB is my all time favorite.

 

[blujax01]

I just picked up this Model 64-8 last week. The box is marked "Brinks I" and is NOS from 2006. I purchased as a closeout from the local armorer. I was told it was left over from when Brinks changed to 40 cal semi-automatics.

 

[vrichard]

also a P.R.2in.
Dick

 

[bananaman]

I currently have a 1905,M&P 4th change that left Smith in June of 1919.( serial# 2996xx) It needs another Smith 38 for company, a Model 64.
My question is, has anybody bought a bobbed hammer 64 law enforcement trade in of this gun? If I do this, what should I expect? It will be a range gun, and I have Crimson Trace laser Grips to put on it to double as a home protection gun. Are + P loads safe to use occaisionally in these? Thanks in advance for your input! Bob

 

[scha]

I bought one of the J&G Model 64-5 ex-law enforcement models and was pleased. It had the Round Butt and I sent it to Smith & Wesson to have a tapered barrel installed. The revolver had scratches in the finish and old rubber grips but the barrel and action were both very good. If you want a range gun or home protection gun I think one of these Model 64s would be a good choice. If you want to spend time polishing the finish, it would look quite nice. +P should be no problem for any Model 64.

Hope this helps.

Steve

 

[bananaman]

Model 64 law enforcement trade in

Yes, that is the one in question! I didn't know if it would worth while persuing. Thanks for the info! Bob

 

[Bat Guano]

I need to be finding one of those $150 M64 standard barrels...