Problem with new M&P 2.0 EZ

Joined
Dec 11, 2012
Messages
32,654
Reaction score
31,354
Location
(outside) Charleston, SC
The gun is absolutely fine and I liked it first outing. However both mags are defective. Several rounds of ammo in each mag hung up several times during each firing. I took the mags out and couldn't eject the rounds with my thumb and then only with difficulty. The rim got hung up on the lips of the mag. I tried Hornaday, Fiocchi, MD Venom, Speer Gold Dot and a couple of others with the mags out of the gun and they ALL hung up a few times for each loading. One mag is slightly better, but still very unreliable. I sent the mothership an e-mail asking what to do.

I'll post any results.

PS. The mag to my original Shield is a fine piece of work of chromed steel and works great. The mags supplied with the EZ appear to be made of aluminum, but I'm not sure.
 
Register to hide this ad
Some magazines need to have the very top of the magazine "Tweaked"
just a little bit to get the round to seat at the correct angle to feed properly,

if the spring is installed correctly, and the ammo pushed to the rear of the magazine.

You can destroy a magazine, if this is not done properly, so know what is needed
before you start bending things out of shape.
 
Being brand new.......

... I didn't want to mess with them and void the warranty. I'm sure a little rat tail file action would clear it up but both mags grab the rim tight as a tick. I can't eject the rounds without depressing the round or the spring.

Anyway, they wanted me to return the mags only. I sent them early this week. We'll see what what happen.

Oh, it's a 9mm.
 
Last edited:
Report: Back from S&W

I sent the mags off and they sent me 2(two) brand spanking new mags. The the problems is they have exactly the same defect. Rounds catch and won't feed.

OK, so do I send the back in order to avoid messing with the mags myself. I would have to wait a couple more weeks to get new mags and they would probably be exactly the same.

I looked at the loaded mags and realized that the rim of the cartridge wasn't catching on the feed lips, but the mouth of the cartridge was catching square on the front of the magazine.

So I decided to make an adjustment. Attached are two pictures. One of me trying to push out a round with my thumb. You can't get it out without depressing the round slightly or wiggling it some until it decides to pop out. Uncontrollably, not a genuine 'ramp feed' action. You can push it HARD and it will not feed.

The next shows the amount of material I sanded off the front of the mag to keep the rounds from catching on it. Seems to run through the gun just great. I'll try it at the range ASAP.
 

Attachments

  • SWmag.jpg
    SWmag.jpg
    69.9 KB · Views: 132
  • MAGSTICK.jpg
    MAGSTICK.jpg
    38 KB · Views: 122
Is there a stainless steel recoil spring and guide rod for this pistol? Bought mine today. OE appears to be plastic.
 
You could use the sand paper to soften the sharp edge of your feed lips on your mags too but since you assumed I might be wrong about mag spring might be in backwards But if you do not check , shame on you . Mean time keep up with the entertainment!
 
Common Problem?

I sent the mags off and they sent me 2(two) brand spanking new mags. The problem is they have exactly the same defect. Rounds catch and won't feed.

OK, so do I send the back in order to avoid messing with the mags myself. I would have to wait a couple more weeks to get new mags and they would probably be exactly the same.

I looked at the loaded mags and realized that the rim of the cartridge wasn't catching on the feed lips, but the mouth of the cartridge was catching square on the front of the magazine.

So I decided to make an adjustment. Attached are two pictures. One of me trying to push out a round with my thumb. You can't get it out without depressing the round slightly or wiggling it some until it decides to pop out. Uncontrollably, not a genuine 'ramp feed' action. You can push it HARD and it will not feed.

The next shows the amount of material I sanded off the front of the mag to keep the rounds from catching on it. Seems to run through the gun just great. I'll try it at the range ASAP.

You have had four brand new mags that all exhibit the same issue. I wonder if this is a common problem among many 9EZ magazines? Has anyone else experienced this issue?
 
You could use the sand paper to soften the sharp edge of your feed lips on your mags too but since you assumed I might be wrong about mag spring might be in backwards But if you do not check , shame on you . Mean time keep up with the entertainment!

Thank you too for the entertainment!

:rolleyes:
 
I have indeed.....

You could use the sand paper to soften the sharp edge of your feed lips on your mags too but since you assumed I might be wrong about mag spring might be in backwards But if you do not check , shame on you . Mean time keep up with the entertainment!

,,,disassembled both mags and there was no problem there. After I disassembled/reassembled them about 4-5 times each I got good at it.:)

Though I thought so at first I don't think the feed lips need any work. The cartridge really seemed to catch on the case mouth. It was the same for all four mags.:confused:
 
Last edited:
The mags wouldn't work.......

Four brand new mags. I would begin to suspect something on the pistol is not exactly right.
'

The mags did the same thing out of the pistol. You can see the picture of me pushing HARD from the back of the cartridge to get it to slide out the mag and it ain't going nowhere. All four mags did this with different ammo. When I took down the front I could unload each mag 'flip, flip, fliip' with my thumb as should be. The first three rounds in the mag were the worst because the spring pressure was stronger holding on to the case mouth.

I'm am going to test the pistol this coming week. That'll let us know if that's the real problem.

My question is doesn't anybody else have trouble with this? Why does S&W put out such sorry mags that could be fixed with a slight modification? I tried to put my original Shield mag in the gun to see if it would work, but it wouldn't fit. So I have a Shield and a Shield EZ that wont use the same mags.
 
I'm going to check it this week.

Four brand new mags. I would begin to suspect something on the pistol is not exactly right.


But the mags acted the same way outside the gun as they did in the gun. You should be able to unload a mag with your thumb easily but these really got stuck on the mag. You could push HARD and they wouldn't come out unless you depressed them or wiggled them some and then they would pop out uncontrollably or stand up and be difficult to remove. Maybe there's something wrong with the gun, but the mags definitely ain't right. I'll try them this week and see if the problem isn't deeper.
 
Back
Top