speed on a single stage press?

[S&W38]

One summer during the early 1970's I prepared for a friend's visit by loading a total of 600 to 650 handgun rounds. I recall 232 .45 Auto rounds, about 100 .357 Magnum rounds and the rest were .38 Special rounds. Starting with fired empty cases, I decapped each one case using a Wilson decapping base and decapping punch, powered with a plastic-faced hammer. I cleaned each primer pocket with an RCBS Crocagator and then carefully inspected each case. I washed the cases in a dishwashing detergent and water solution, taking care to wash each caliber separately. I put the cases into a plastic one-gallon milk bottle, squirted in some detergent, filled the milk bottle with hot water, screwed on the cap, and shook each batch for about 15 minutes by turning the bottle upside down and back, over and over. I rinsed by dumping the filthy wash solution, and then I rinsed with hot water several times, using plenty of the same kind of agitation with each change of rinse water. When no more foam formed in the rinse water, I dumped the final rinse arranged the clean wet cases on paper towels to air dry, and then did the next batch. I carefully inspected the dry cases. I loaded the cases using my RCBS Junior press, RCBS adjustable powder measure, RCBS Carbide dies, Flambeau loading blocks and RBCS Case Lube. Then I carefully wiped off all the sticky RCBS Case Lube from each and every round, one round at a time. I spent at least 30 hours on that project. I did not load any maximum loads. All the .45 Auto rounds worked perfectly in the M-1911; the .38 Special and .357 Magnum rounds functioned perfectly in S&W revolvers. All rounds were expended during one afternoon at an unsupervised informal range. Is it any wonder that the .22 Long Rifle is my favorite handgun and rifle cartridge? I know about progressive presses, I just can't afford one yet. I have also taken note of Hornady's One-Shot spray case lube.

 

[scooter-2]

speed on a single stage press;

thanks for all of the replies. it is interesting to hear all of the different opinions. i have loaded for 25 years. i know saftey is the first concern. i was just trying to see what different ideas everyone has. thanks; scooter-2

 

[358156hp]

I just finished extensive research on this issue, and in so doing, have set a new worlds speed record for loading 100 quality 357 magnums on a single stage press. The procedures involved include:

Selecting 100 brass cases
Measuring 100 cases.
Tumbling 100 cases. Includes changing the media in the tumbler.
Full length sizing all 100 cases.
Re-measuring all 100 cases.
Trimming all 100 cases on a Lyman Power Trimmer.
Deburring 100 cases, outside only.
Checking the primer pockets for uniformity in 100 cases.
Deburring the flash hole in 100 cases.
Flaring the case mouths of 100 cases. includes searching for the case flaring die I haven't used in 10 years.
Cleaning surface rust from the case flaring die & oiling it.
Removing the oil from the case flaring die (oops!)
Tumbling 100 cases again, with polish to remove my paw prints
Cleaning tumbling media from the flash holes in 100 cases.
Priming 100 cases with my RCBS hand primer thingie.
Selecting 100 140 gr Hornady bullets from my stock.
Researching & selecting suitable reloading data.
Locating my old Hornady powder measure & changing the drum over to the proper style.
Setting up the Hornady measure & calibrating my equally elderly Hornady powder scale.
Charging 100 fully prepped cases with AA#9.
Changing over to my bullet seating die & adjusting said die.
Seating 100 140 Gr Hornady bullets in the prepped, charged cases- no crimp applied.
Change die to a Redding Profile Crimp Die, and adjust.
Crimp 100 loaded 357 magnum cartridges.
Search for an unused 100 round MTM box for my treasure.
Inspect & box 100 loaded 357 magnum cartridges, and label the box.

I accomplished this simple series of tasks in a blistering 4-1/2 days, pausing only to eat, sleep, work 10 hours a day for two of those days, go to the store, watch television, and talk with the neighbor a bit. And go to the gun store. I'm confident this new worlds record will stand for a long time. I have enclosed the manufacturers name for my major reloading tools, since I know there could be a major sponsorship offered at any moment.

 

[CGT80]

So. Need a little advice. I'm loading 10MM in a single stage. I'm shooting IPSC (for the first time in years) and finding that HOLY **** I'm shooting a lot more.

I batch my reloads. I.E. I deprime a bunch. I prime a bunch. I flare a bunch and then I load a two or three hundred at a time. This is over several days/weeks.

I'm looking at moving to a progressive but the cost is making me gulp a tad.

However those folks at Lee have a caliber specific press set for cheap money. Much less expensive than Dillon etc. The reviews are pretty reasonable and I wanted to know if anyone here has had any experience with these things. For $180 I don't expect a world beating press but I'm wondering if I should go this way or just bite the bullet (if you'll excuse the expression) and spend $750 on an RCBS or Dillon.

I figure I'll load around 1200 to 2000 per year.

Any and all suggestions welcome

I tried to get a lee progressive going for my grandfather. He had issues with it. I didn't have the patience. Save yourself the hassle and money and consider something like the SDB from dillon. It takes dedicated dies. I don't know if it will do 10mm or not. It is the least expensive dillon progressive.

At only 1200-2000 rounds per year (assuming only one caliber), I would just load single stage.

I load many calibers and go through many rounds a year. The dillon 550 is awesome for that.

1200 rounds of 9mm only lasts one day in my house. I use a 1050 dillon just for 9mm.

 

[papajohn428]

I had the Lee Progressive, I think it was called the Loadmaster.......5 die stations. I got it and loaded a thousand rounds with it, learning what to watch for. It took a LOT of tweaking, little things, constantly. The case feeder was the worst part, I'd tighten it down and in ten rounds it would work loose again. I eventually got sick of spending more time readjusting things than loading, and sent it back. I still do 250-300 rounds an hour on my Lee Turret, starting with prepped/primed brass. That's fast enough for me.

 

[brucev]

I load .30-06 rifle rounds in 100 round batches. I normally can load 100 in an hour from start to finish. Normally I have several hundred cases prepped for use. For pistols, I can load 100 .38/.357 rounds per hour if I have all my components at hand, etc. I use a RCBS Sr. press and RCBS die sets. I neck size the .30-06 rounds as I fire them in my 1903 and 1903-A3 rifles. When using my M-1 Garand, I full-length size the brass. I use a carbide die when loading pistol rounds. This makes the process go faster. I use the .30-06 rounds for vintage military rifle matches in which I usually do very well. My favorite match load averages 96.9 for the last 17 matches. My pistol loads are plain vanilla... usually 158 gr. LSWC's and 5.0 gr. of Unique. It is a load that has given excellent results in my revolvers ever since I first loaded it in 1982. JMHO. HTH. Sincerely. brucev.

 

[mr-mom]

I use reloading as my pressure relief valve. It is relaxing and very satisfying. Every bit as much fun as shooting the darn things. At my age, I don't speed anywhere!!