Flash hider removal

[yugowego]

I must of lucked out... Mine wasnt on very tight at all... It was about as normal as my ARs.

 

[roadkill45]

i've always used wood blocks in the vice, never had a problem getting any type end attachment off. although before even trying i heat the end up with torch just in case any locking agent was used.

once off, i always put some anti seize on the threads before putting on a can or other FH, then 1/4 turn past hand tight. never had one come loose on me yet.
matter of fact i think the anti seize evaporates after the barrel gets hot say in a mag dump and it kinda 'welds' it to the barrel, plus the barrel swells when hot due to heat expansion. i had one AR barrel that i put in the freezer for a couple hours and it came off almost by hand due to the steel being cold and releasing some of it's hold on the threads.

if i use any locking compound it is almost exclusively clear nail polish. just enough hold but not so much as to take superman to get it off again. in the field i have a 1/2" open end wrench that i have sawed in a little more than half in two and it goes in the pistol grips of my AR's. i can change devices very easy w/o a vice since they are only a little more than hand tight (if not dedicated and using the nail polish).

 

[rimfire22]

I cranked down on the vise a bit more, used a heat gun to warm up the flash hider and with a good tap to the wrench with a hammer, the flash hider broke free.

The Aluminum marks come off easily with a rough sponge/nylon and brass brushes/terry cloth and some oil.

Nylon brush wasn't enough, but a brass brush and some oil took care of it.

 

[rimfire22]

Couple of follow-up questions:
1. When tightening the T22 handguard converter, and then, the barrel nut wrench, you should be holding the barrel, not the upper, correct? Or is there no risk of damaging the upper by holding it for these tightening tasks?

2. Once a longer handguard is installed, how do you tighten and subsequently loosen (if you needed to) the flash hider? There isn't enough room to get vise jaws on the barrel. I suppose a pair of pliers and some inner tube on the exposed length of barrel will let you achieve sufficient torque to keep the FH in place and loosen it in the future. Any other suggestions with respect to this?

 

[Hobie1]

I'd guess using nylon jawed plumbers pliers might work but you absolutely cannot torque the upper. Replacement of said upper will follow. As stated earlier, let the crush washer do it's job and you don't to need to put a lot of torque on the F/H.

Hobie

 

[tacticool22]

Couple of follow-up questions:
1. When tightening the T22 handguard converter, and then, the barrel nut wrench, you should be holding the barrel, not the upper, correct? Or is there no risk of damaging the upper by holding it for these tightening tasks?

2. Once a longer handguard is installed, how do you tighten and subsequently loosen (if you needed to) the flash hider? There isn't enough room to get vise jaws on the barrel. I suppose a pair of pliers and some inner tube will let you achieve sufficient torque to keep the FH in place and loosen it in the future. Any other suggestions with respect to this?

1) Yes, always hold onto the barrel whenever possible when you tighten the factory barrel nut, my converter or a FH/MB.

2) After the adapter nut is torqued the free float hand guard can be tightened with the barrel in the vise jaws, or if you hold the upper and lower put together (insert safety stuff here) without too much worry about the barrel turning in the upper. You would have to torque the hand guard more than you torqued the converter to start any kind of bad spin.

There are some wrenches that have a rubber strap that work very well.

 

[RV4driver]

After reading these horror stories about not being able to take off the FH, I attacked mine with some trepidation. It practically fell off. Actually, I was disappointed! I put my flash-hider/suppressor QD on, and used some "blue-pen" on the aluminum marks on the barrel.

Apparently, there is some variation...to say the least, on the amount of torque on that flash hider.

 

[Brett248Vista]

Just to take a little time to explain why you do not hold a 15-22 by the upper to do any of this type of work. On the 15-22 unlike an AR, the barrel is inserted through the upper receiver from the backside, the nut then threads onto the barrel from the front (as normal) but it actually pulls the barrel and sandwiches it between the nut and the upper receiver. Inside the upper receiver there is a steel insert that takes all the squeezing pressure. But the ONLY thing that stops the barrel from turning in the upper are a pair of small ears on the chamber block, these ears engage plastic slots in the upper (the same slots that the bolt rails interface).

If you attempt to tighten things or loosen things using the receiver and not holding the barrel it can and will spin inside the upper. If the rifle is fully assembled when this happens it will also bend the bolt rails. If the rifle is not assembled it will gouge out the plastic that the ears align into.

Hope that helps explain the "why".

 

[ericlw]

and to think a few weeks ago i was insulted by several people on here for having to cut the flash hider off my mine as if i was incompetent fool.

 

[rimfire22]

Just to take a little time to explain why you do not hold a 15-22 by the upper to do any of this type of work. On the 15-22 unlike an AR, the barrel is inserted through the upper receiver from the backside, the nut then threads onto the barrel from the front (as normal) but it actually pulls the barrel and sandwiches it between the nut and the upper receiver. Inside the upper receiver there is a steel insert that takes all the squeezing pressure. But the ONLY thing that stops the barrel from turning in the upper are a pair of small ears on the chamber block, these ears engage plastic slots in the upper (the same slots that the bolt rails interface).

If you attempt to tighten things or loosen things using the receiver and not holding the barrel it can and will spin inside the upper. If the rifle is fully assembled when this happens it will also bend the bolt rails. If the rifle is not assembled it will gouge out the plastic that the ears align into.

Hope that helps explain the "why".

Thanks for the detailed explanation.

Fortunately, if the bolt isn't in the upper, it sounds like the only thing that will get damaged is the upper, and per your parts list, that can be replaced for $20 plus shipping, so definitely not the end of the world.

 

[rimfire22]

To anyone reading this and contemplating removing their flash hider, I would make sure you clamp the barrel tightly. That was my problem - the barrel would turn as I tried to loosen the barrel nut. My vise was free standing so I was holding the vise down with one hand while tightening the vise jaws with the other hand. Yeah, dumb. And definitely couldn't tighten the vise jaws enough with this retarded method. After mounting the vise, I tightened the vise jaws using both hands and voila, FH broke free.

My suggested routine to making sure you get it off without any drama:
1. Optional: Put a drop or two of liquid wrench (or similar) on the flash hider nut and let it sit for a few hours. You can get it off without this, but it won't hurt anything and might make it a little easier.
2. Clamp the barrel really tightly (using aluminum, polymer, wood for vise jaws). If the barrel spins when loosening the FH, it's not tight enough. If you are like me and have your vise free standing, bolt it down to a bench or some wood (if the latter, get a friend to hold the wood and vise down while you turn the handle).
3. Optional: Heat up the FH nut with a heat gun if you have one. Again, may not make a difference, but won't hurt anything.
4. Use a hammer to tap the wrench. Impacting the wrench will break the nut free more readily than applying steady torque.

 

[subbyc]

Hey there, thanks rimfire22, I had the same problem trying to remove my flash hider. I had padded the barrel with soft wood but that twisted in my vice and has scored the finish on the barrel so I will have to re-finish it, probably with krylon paint as it is under the fake suppressor anyway. I ended up using hard wood pads in the vice, a blow torch, wrench and hammer. I couldn't believe how tight the vice had to be as well but it came unstuck eventually. I don't think there is any need for the flash hider to be that tight though. All is good now though

 

[tomcatt51]

I had padded the barrel with soft wood but that twisted in my vice... I ended up using hard wood pads in the vice...

My vise blocks are just 2 pieces of pine 2x4, clamped together and a 5/8" hole drilled for the barrel to sit in. A .625" hole seems to have about the right crush on a .670" barrel. Worked great, my flash hider was a tight one. If it's not enough in the future I'll make another set of blocks from hardwood.

 

[subbyc]

I guess the problem I had was that my wood didn't have a slot for the barrel to fit into so the friction between the wood and the barrel was only along a narrow line. The grove or slot would allow for a greater surface area which would make for an easier job I guess. Lesson learned. The soft wood was really soft and split/twisted in the vice when I applied pressure with the wrench, hence the score in the blue ��

 

[tomcatt51]

I guess the problem I had was that my wood didn't have a slot for the barrel to fit into so the friction between the wood and the barrel was only along a narrow line.

Yes, you need an undersize hole so it deforms and gets a really good "bite" on the barrel. The hole is drilled across, not with, the woods grain. I much prefer wood blocks over the aluminum V blocks.