Since the 357Sig does not fit into the numbering system of the 9s',40s',&45s' and to differentiate it from the 357Magnum,I'll create the new numbers of 357S13,357S53,357S06 etc.
If you could design your own S&W auto pistol.....
- Thread starter policerevolvercollector
- Start date
...................... I'm almost there now!!!!!! but would add 39 style grip frame to take wood panel grips....................How about a SD-9 ..... but with an alloy frame,Novak night sights .....and oh ya.....reverse two-tone!
DD357
Member
Already on the chart 3953.
- Joined
- Dec 2, 2012
- Messages
- 3,347
- Reaction score
- 5,573
A CS10. I don't want to fire it, but I want to own it!
muzzleblast
Member
OlongJohnson
Member
- Joined
- Oct 30, 2015
- Messages
- 55
- Reaction score
- 43
A 3953TSW with no accessory mount or dust cover grooves, and an H&K LEM/Match hybrid trigger. While they're at it, a modern Melonite/Nitron/etc. black finish on the slide and black anodized frame.
But if we're settling for things S&W might have actually made but didn't, I'd settle for a 3956.
But if we're settling for things S&W might have actually made but didn't, I'd settle for a 3956.
I'd start here, but with a few changes. 9mm instead of .45 ACP. Or maybe they could make both!
Somebody else mentioned it, but I'd change the grip mounting to be like the 2nd generation. That would open up a lot of possibilities.
Titanium frame would be nice, but would cost as much as Unobtainium, so it would be alloy much as it is now.
Frame mounted decocker, night sights, Melonite finish on the slide, dark finish in the frame.
Integral rail for those who want or need to mount a light, laser, bayonet, etc...
De horn it all around to slim the profile as much as feasible, especially at the rear of the trigger guard where it is supposed to blend into the frame.
Somebody else mentioned it, but I'd change the grip mounting to be like the 2nd generation. That would open up a lot of possibilities.
Titanium frame would be nice, but would cost as much as Unobtainium, so it would be alloy much as it is now.
Frame mounted decocker, night sights, Melonite finish on the slide, dark finish in the frame.
Integral rail for those who want or need to mount a light, laser, bayonet, etc...
De horn it all around to slim the profile as much as feasible, especially at the rear of the trigger guard where it is supposed to blend into the frame.
Shadow1006
Member
Well based on the older info I included below: here is mine which I also posted in the "Wish List" sometime back;
The 1016 would be very nice. However, I had always wanted a 6" or 7" slide model of the 10XX series pistols for hunting with the 10mm cartridge. This particular firearm Performance Center 1096 because it could have four 6" or 7" barrels with fully supported chamberings for the 10mm, 40S&W, 357SIG and the 9x25 Dillon cartridges to add to its flexibility as a shooter/hunter piece. The slide could be offered cut for mounting optics such as red dot or even picatinny to accommodate other scopes.
The action could be DAO like the 86's and 46's or TDA type with decocker like the 06's and 66's.
I hate to say this, but it might could sport a 1911 type grip safety and thumb safety to allow Cocked and Locked carry...SAO ???
3rd Generation Model Codes
22xx = .22 rimfire
39xx = single stack 9mm
59xx = double stack 9mm
69xx = compact double stack 9mm
10xx = 10mm
40xx = .40 S&W
45xx = .45 ACP
35xx = .357 TSW
xx0x = full length barrel TDA
xx1x = compact barrel TDA
xx2x = full length barrel Frame Decocker
xx3x = compact barrel Frame Decocker
xx4x = full length barrel DAO
xx5x = compact barrel DAO
xx6x = mid size barrel TDA
xx7x = mid size barrel Frame Decocker
xx8x = mid size barrel DAO
xx9x = Special Order
xxx0 = Scandium frame
xxx3 = Alloy frame silver
xxx4 = Alloy frame black
xxx5 = Steel frame blue
xxx6 = Stainless frame
xxx7 = Non standard combination
xxx8 = Special Order
The 1016 would be very nice. However, I had always wanted a 6" or 7" slide model of the 10XX series pistols for hunting with the 10mm cartridge. This particular firearm Performance Center 1096 because it could have four 6" or 7" barrels with fully supported chamberings for the 10mm, 40S&W, 357SIG and the 9x25 Dillon cartridges to add to its flexibility as a shooter/hunter piece. The slide could be offered cut for mounting optics such as red dot or even picatinny to accommodate other scopes.
The action could be DAO like the 86's and 46's or TDA type with decocker like the 06's and 66's.
I hate to say this, but it might could sport a 1911 type grip safety and thumb safety to allow Cocked and Locked carry...SAO ???
3rd Generation Model Codes
22xx = .22 rimfire
39xx = single stack 9mm
59xx = double stack 9mm
69xx = compact double stack 9mm
10xx = 10mm
40xx = .40 S&W
45xx = .45 ACP
35xx = .357 TSW
xx0x = full length barrel TDA
xx1x = compact barrel TDA
xx2x = full length barrel Frame Decocker
xx3x = compact barrel Frame Decocker
xx4x = full length barrel DAO
xx5x = compact barrel DAO
xx6x = mid size barrel TDA
xx7x = mid size barrel Frame Decocker
xx8x = mid size barrel DAO
xx9x = Special Order
xxx0 = Scandium frame
xxx3 = Alloy frame silver
xxx4 = Alloy frame black
xxx5 = Steel frame blue
xxx6 = Stainless frame
xxx7 = Non standard combination
xxx8 = Special Order
LOL I think that's called a Model 41.......
I've got ,22 kits for my Browning HP and Beretta 92.... but a 4-4.5 inch Model 39 in .22lr would be sweeeet!!
nocents
Member
from post #24-a CS10
CS10s' are already being made(by us,not S&W)by converting CS40s'.
4013/4014/4053/4054 are also converted to 10mm. There are threads in this auto pistol forum concerning the conversion.
But yes it would have been great if S&W made a CS10 along with the CS9,CS40,CS45.
CS10s' are already being made(by us,not S&W)by converting CS40s'.
4013/4014/4053/4054 are also converted to 10mm. There are threads in this auto pistol forum concerning the conversion.
But yes it would have been great if S&W made a CS10 along with the CS9,CS40,CS45.
- Joined
- Dec 2, 2012
- Messages
- 3,347
- Reaction score
- 5,573
Yessir, I've seen some of those beauties. They look great. S&W should've produced them when they got the FBI contract as a BUG for the agents.
mike from st pete
Member
A 4-5-639 without the winged adjustable sight and the god awful trigger guard hook.
special reserve
Member
- Joined
- Nov 9, 2013
- Messages
- 18
- Reaction score
- 4
Any stainless 10mm in a double stack, wow!!!!!!! Friggin awesome. I've wondered how much it would cost to have one made........
twistedracer
Member
Not 10mm but still:
[ame="https://www.youtube.com/watch?v=3tEYcUSQDyw"]https://www.youtube.com/watch?v=3tEYcUSQDyw[/ame]
RV4driver
US Veteran
I don't care what it looks like, or what it's made of. I only have two criteria: it's reliable, and it always hits where I wanted to hit, whether it was aimed properly or not.
Wow! You just described my 3013NL! And, frankly, my Israeli trade 3914.
RV4driver
US Veteran
Ditto on the finger hook on the trigger guard. AND the wings on the rear site. Seriously, those made it into production???
Similar threads
