I have had a 325NG for about 5 weeks and really like shooting it. What I would like to find is 2.5 or 3 inch steel frame 45 acp. S&W's web site doesn't show one. My question is did smith make a short barrel steel 45acp? I think I know what I am saying hope every one else does.
625 45acp short barrel ?
- Thread starter grover99
- Start date
Register to hide this ad
Messer
Member
Yes they did - I have a 625-3 in 3"...
Bob S.
Bob S.
very desirable, very hard to find (at a decent price)...and S&W is foolish for not making more of them!!!
OP
Story of my life. I want something that is hard to find and cost alot. Well maybe I will get lucky.
David Sinko
Member
I bought a 2" barrel from Numrich and had it installed on my 625-4. It worked out very well and I'm quite pleased with it. It didn't cost as much as I thought it would, though my gunsmith isn't too eager to do another one of these any time soon.
Dave Sinko
Dave Sinko
OP
Well I could pick up a 625JM and have the barrel replaced. But I bet I am looking at well over $1000 in the end.
I have one of those Numrich barrels and believe they were intended for the lightweight fixed-sight Performance Center revolvers (625-10, for example). Did you have to have a special front sight mounted to make use of the adjustable rear sight on your 625-4?
I bought the barrel because I thought I would someday come across a 1917 or Brazilian that was sound but for a bad barrel. I was going to make a two-tone belly gun. But then a few days ago I stumbled across a 625-3 at my LGS and committed to that. I'm not giving up on the project, but the urgency has certainly been reduced.
I don't think you are necessarily in four-digit territory if you want to pick up (or build) a three-inch 625. While the three-inch 625-3s are in demand and seldom seen, they are not flat-out rare. I picked up one recently when I stumbled across it at my LGS. It needed a bit of attention (action was unlubricated and there was a little carbon grime in the nooks and crannies), but in general it was obviously little fired and still had its original box. The asking price was $900, but I got it out the door for less than that, including tax and the California transfer fee. If this gun can be had at that price in CA, I have to believe that even better deals can be found in other states.
The message is: Take heart, and don't stop looking. You will find what you want.
Those are the LONG barrel snubbies
The short ones are 2"
However the factory ones were fixed sight and Scandium frames
They were made in 45ACP and 45Colt
When these were in production, I bought 5 extra barrels so I could build up a few
on stainless adjustable sight 625s
Just have not done it yet
The short ones are 2"
However the factory ones were fixed sight and Scandium frames
They were made in 45ACP and 45Colt
When these were in production, I bought 5 extra barrels so I could build up a few
on stainless adjustable sight 625s
Just have not done it yet
Last edited:
What's a CLT? Is that anything like a CTG?
What's a CLT? Is that anything like a CTG?
The barrel was just too short for the word COLT
Messer
Member
This is true - a buddy of mine that loved my 625 3" found one recently at a local gun show for $600.00, so good deals can be found.
Good luck with the search,
Bob S.
Erich
Member
Had to put in a pic of mine. 
I was working in a gun store when these were released in the late '80s - I thought the concept was insane. Who would want a revolver when he could have a semiauto? That held more rounds! Then I grew up . . .
I was working in a gun store when these were released in the late '80s - I thought the concept was insane. Who would want a revolver when he could have a semiauto? That held more rounds! Then I grew up . . .
Old Fashioned Six Shooter
Member
- Joined
- Dec 16, 2011
- Messages
- 72
- Reaction score
- 13
I would buy a 625 Performance Center UDR in a heartbeat if S&W would just make one for me. I love my 627 PC UDR. A .45 ACP version of it would be awesome as well.
very desirable, very hard to find (at a decent price)...and S&W is foolish for not making more of them!!!
That and the 624. I don't have a problem with the locks but scandium belongs in a MIG-29, not a revolver.
I'm working on one. Converting a 629UDR to .45ACP. Let you know how it turns out.
Frank Ruple
SWCA # 2087
papajohn428
Member
Had to put in a pic of mine.
I was working in a gun store when these were released in the late '80s - I thought the concept was insane. Who would want a revolver when he could have a semiauto? That held more rounds! Then I grew up . . .
DANG it Erich............I used to like you. It's not fair that you have one, and I don't. And you probably got a smoking deal on it too. Keep this up, and you're gonna give lawyers a bad reputation!
Similar threads
- Locked
