Frog Lube opinions

captcook

captcook

Member
Joined
Mar 20, 2014
Messages
231
Reaction score
132
Location
S.Eastern North Carolina
View attachment 153099
Just cleaned and treated my pistols with frog lube. Anybody else tried this product and if so what is your opinion ? The science of it makes sense but being my first time using it I just wanted to get some feedback.
Thanks
 
Last edited:
Register to hide this ad
I have been using it on my handguns for almost a year. Seems to work well. It does require a bit of initial "set up" but then works great. Be sure to follow the instructions and heat the metal before applying the paste. After doing this 3 times, I have not applied the paste at all since and just use the green liquid. The barrel cleans easily and quickly. I have cleaned some of my handguns a bunch of times since the first initial application and so far no signs of needing to do the paste again yet. I plan to reapply the initial paste procedure about once per year. Other handguns have not been used much since first application so I can't comment on them but I have 3 or 4 that have been cleaned a lot.
I have not used it on my AR-15s or AK 47 yet but I may at some point.
 
I have FrogLube on the internals of the 642-1. It works great. My revolver is just as smooth as when I used a little conventional lubricant.

People who have experienced difficulties generally left a visible layer of FrogLube on the surfaces they lubricated and had the excess inhibit the movement of their gun's action at some point, usually in very low temperatures.

Used on external surfaces, like cylinders and the frame near the forcing cone, even if you "wipe it all off" there may be enough to create a little black gunk when you fire the revolver. I believe the manufacturer even cautions you about this phenomenon. If you wipe the black gunk off while the gun is still hot, no worries!

My cylinder is titanium, intended for a 340PD. Either the coating S&W uses or the metal itself seems to have prevented me from enjoying the "effortless carbon deposit cleaning" that some other people report with FrogLube. Oh, well.

I recently bought a two ounce container of FireClean, for about the same cost as the four ounce container of FrogLube paste that I chose. I have only used it on the cylinder and for only one shooting session, so far. It made carbon removal after shooting a little easier that FrogLube did for me.

Neither is quite as magic as I would like, but the FireClean comes closer for me and it is pretty much impossible to over apply because it resembles Mobile1 synthetic oil in appearance and does not require a heat lamp. I am also pleased that it is completely odorless.

Both manufactures recommend using as little of their product as possible for best results. Tiny amounts of FireClean on the cylinder yoke spindle provide very smooth operation, for me.

As always, YMMV.
 
Last edited:
I bought a Sig 220 Elite that had been treated with FrogLube. Felt slick as snot on a doorknob. Jams and failure to fires were common. Spent several hours in a detailed strip and cleaning noting that the pins were all hard to remove and left a waxy residue around the holes when the pin finally came out. Firing pin and spring were gummed with the same waxy residue.
Long story short after a thorough striping and proper lube with oil and grease as required the pistol was put back together and has functioned PERFECTLY since. NO parts were replaced.
My opinion: Anything that can cause misfires if applied improperly has no place on any of my guns and I would never buy or use it.
Chip King
 
I have used FL on all my M&Ps and have not had any problems. Great stuff when used as directed.
 
My LGS said to just "Gom it on my gun" I think he may have misinformed me of course I did not "gom" it on and put on a light coat on hot parts. But I will give it a chance they have had one treatment and I will do two more before I make my decision. My LGS said "bring it in and and we will do the first treatment for you" I had my M&P 9 with me but I decided against letting him touch it I think I made the right choice.
 
I use FL on all my guns, I shoot around 1200 rounds per week. No failures. I think the people that have problems with it are putting too much on. I use the paste, brush it around and then remove as much as I can find. Every time I see a picture with streaks of grease on the slide or drops of oil on the barrel it makes me cringe. The picture below is at around 35K rounds on one of mine.
 

Attachments

  • IMG_20140402_131831_481 (Small).jpg
    IMG_20140402_131831_481 (Small).jpg
    84.4 KB · Views: 180
I have used it for over a year on all my poly semi autos and every steel revolver I own. I do use as little as possible, and have not yet had any any issues other than it takes me half the time to clean my guns that it did when I used solvents and oils.
 
I got some to test to see if it lived up to all the hype, it worked OK for me, nothing special though. It seems to me like a very expensive version of T/C Bore Butter, and does not remove carbon fouling as well as the home brew Ed's Red. For me the bottom line is I guess it works, But I will continue to use bore butter on my Black Powder arms and ER on my smokeless cartridge guns.
 
wingnuut said:
if any gets in the stricker channel your in trouble it hardens up , why use something you have to worry about
Click to expand...

If ANYTHING gets in there you are in trouble! The stiker channel should ALWAYS be clean & dry & free of ANY cleaners or lubricants.



I have been using frog lube for a few years now on both my f/s 9 & my 9c & I gotta say its without a doubt the BEST product I have ever used!!
 
I have used it since January, 2014 on my Shield 9mm and 2 H & K'S and am very satisfied with it. As said, best if you make sure to remove all excess. Initial application with heating the parts is time consuming but worth it.
 
I am continuing to use Breakfree CLP in general, with the somewhat thicker Breakfree LP on slides and barrels. I am using W25B, which is recommended by Sig, on my SP2022 as a sort of long term experiment. The kit came with oil, grease, and cleaner.

In the past I tried lubriplate but ended up with dried, hardened goop on key parts. Probably would work fine if applied right before use and removed right after use; that's too much work for me.

I am sold on the idea of grease of some sort on slide rails and barrels, with oil on everything else -- I am trying two separate "systems" (one petroleum based and one not) and am enjoying good results with both. How does that answer the OPs question on Frog Lube? 1. I believe the comments on following instructions. 2. Breakfree CLP and LP are the "standard" and make a good base for comparison of results. Good luck with the FL.
 
Kanewpadle said:
Been using Tetragun for over ten years. It's all I need.
Click to expand...
Probably so, sir!

Some of us more gullible folks, that would include me, feel a need to waste $14.95 on the latest wonder snake oil from time to time, just because we can.

Some have worked our remarkably well. WeaponShield comes to mind in that category.

But, most are a bit like the last two I tried FrogLube and FireClean. They offer amazing promises but don't quite meet my resulting expectations.

Fortunately, I still have a healthy supply of the tried and true products. My various firearms seem to like that.

Still, it is cheap entertainment . . . so, what's next? ;)
 
Been using it on my handguns for about a year and no issues. Will be switching the long guns to it when the large bottle of hoppes I bought before I found Frog lube runs out.
There have been reports claiming that frog lube has resulted in stuck firing pins but not a single one that I have read gives any details regarding now it was applied or how "wet" the gun was left after treatment.
I will likely redo the initial treatment process on the handguns at some point this summer as routine maintenance especially now that I have a more effective heating method than when I first used it.
 
TucsonMTB said:
Probably so, sir!

Some of us more gullible folks, that would include me, feel a need to waste $14.95 on the latest wonder snake oil from time to time, just because we can.

Some have worked our remarkably well. WeaponShield comes to mind in that category.

But, most are a bit like the last two I tried FrogLube and FireClean. They offer amazing promises but don't quite meet my resulting expectations.

Fortunately, I still have a healthy supply of the tried and true products. My various firearms seem to like that.

Still, it is cheap entertainment . . . so, what's next? ;)
Click to expand...

Waste? I don't think so. ;)

A good lube/cleaner is an investment.:eek:

If you really want to be cheap, buy a big jug of Mobil One. It works good too!!;):o Last ya a lifetime.
 
You must log in or register to reply here.

Similar threads

Narragansett
The New Finishes and Solvents
Replies
9
Views
336
MyTurn
M
S
How to clean a S&W 361c
Replies
0
Views
83
Supertrooper
S
W
New here, hello from the midwest
Replies
16
Views
343
sophie
sophie
Narragansett
Another Lubrication Thread
2 3 4
Replies
70
Views
4K
45Smashemflat
4
chief38
Suppressors - do they make sense? If they do, then when?
2 3
Replies
41
Views
1K
WCCPHD
WCCPHD

Latest posts

Back
Top