s&w 19-2 mfg date
- Thread starter CaptJack1
- Start date
Register to hide this ad
That's a very nice 19, however, that is not the serial number. Serial number will be on bottom of frame where grips are. You will have to remove the grips to read the number. Number you gave is an assembly number used to keep parts together, frame, side plate, yoke, etc.
OP
Great information and education I did not know that I will try to get the serial number from the dealer. I didn’t think it looked correct
thank you very much.
I can't tell because of the target stocks that pre-date the 19-2 by quite a few years, but if the 2 1/2-inch barrel is original and the revolver has a square butt, I think it is a rare variation. I know of only two in existence that letter.
Bill
Bill
OP
Bill….that is so interesting, will post pics when I get it later this week.
I didn’t think these were the original stocks….any idea what the original stocks look like? Would it be worth trying to locate some?
Thanks again
That is a 2.5” round butt Model 19-2 with a set of non-relieved target stocks from a square butt revolver. It came with round butt Magna stocks originally. The Model 19-2 was made from about 1963 to 1966, so the s/n range will be from about K515xxx to K715xxx. What is the LGS asking price? If it has the original box and tools, I think around $800-$900 would be fair, maybe a little less because of the non-original stocks. If just the revolver alone, I’d offer $600 and see what the counter offer is. It is a fine looking revolver, and if in mechanically sound condition, i.e. no discernible endshake, no push off, and smooth trigger pull with tight lockup and minimal flame cutting, I’d go to $700. Also be sure to check the forcing cone area with a good light and magnification for any cracks. Just remember tax and background will add to it, so even at $700, you’re still looking at almost $800 out the door.
Last edited:
OP
tlawler...thanks, great info.
Price is 750 out the door as it is a consignment.
Picking up later this week, will post some pics
Thanks again
Price is 750 out the door as it is a consignment.
Picking up later this week, will post some pics
Thanks again
Engine49guy
Member
My friend recently sold his like new 19-2 snub for $1k,
Ive never seen a snub 19 with a square butt frame , all have been round butt and wearing non diamond Magnas but anything is possible with SW.
The non relieved stocks are way earlier as stated,
On a side note, I suspect it shipped with Magna stocks only because theres no serial stamped in the yoke cut but if it is a square butt frame that just means it shipped with magnas.
Its not a converted 4" because the topstrap has the snub lines.
Ive never seen a snub 19 with a square butt frame , all have been round butt and wearing non diamond Magnas but anything is possible with SW.
The non relieved stocks are way earlier as stated,
On a side note, I suspect it shipped with Magna stocks only because theres no serial stamped in the yoke cut but if it is a square butt frame that just means it shipped with magnas.
Its not a converted 4" because the topstrap has the snub lines.
I have a 2-1/2" 19 but mine is a -3 model. Round butt but I put some nice rosewoods on it. Also have a 19C Performance Center. These are perfectly sized carry guns for a serious carry caliber.
Forgot about that. Would you have the side by side comparison pic? I have seen the pic in the past but not sure which thread.
What's a 19C?
Engine49guy
Member
The 19-2 snub was the first 19 snub and had a fairly short production run compared to the 19-3 which is the same gun but with the new rear sight leaf screw location.
Those non relieved target stocks have a much higher value ( like $250) compared to non diamond magnas ( like $65 ).
Those non relieved target stocks have a much higher value ( like $250) compared to non diamond magnas ( like $65 ).
Engine49guy
Member
Looks like a Performance Center K comp or am I missing something?
Yeah, pretty much. Stock pic, not my gun. I swapped out the lock with a kit that blends well. But it balances SO well when compared to the average K-frame. Hold one & you'll see what I mean.
Engine49guy
Member
To the OP, once you remove those target stocks establish if it is a round or square grip frame, if its square it is a very uncommon variation and you should letter it because if it shipped that way its worth alot to a collector.
If it has a round butt grip frame the original stocks would look like the top pic.
Paplinker asked for a comparison pic of the 4" frame,
if you compare where the top pics frame meets the barrel you will notice its straight when compared to picture two below which is how the 4" and 6" frames "step" down to the barrel.
Bobs guns
Pic 3 is of a 19-5 (L) and a 19-7 K-Comp, the K-comps are an interesting variation.
If it has a round butt grip frame the original stocks would look like the top pic.
Paplinker asked for a comparison pic of the 4" frame,
if you compare where the top pics frame meets the barrel you will notice its straight when compared to picture two below which is how the 4" and 6" frames "step" down to the barrel.
Bobs guns
Pic 3 is of a 19-5 (L) and a 19-7 K-Comp, the K-comps are an interesting variation.
Attachments
Last edited:
Here’s some early Model 19 snubby porn to enjoy until you get yours in hand. M19-3 on top and M19-2 on bottom. My -2 is a little rough finish wise, but a heck a of a shooter. I like Combat Stocks on my K-frame snubbys.
Last edited:
