Lock Rings for Reloading Dies - Should You Use Them ?

Rollbar

Rollbar

Member
Joined
Jun 16, 2012
Messages
485
Reaction score
71
Location
Florida
I am looking into using lock rings on the LCTurret 4 hole head using the Lee dies 7/8"-14 thread to keep them in place.

Question, should I even use the lock rings first of all.

Question, are these good (link below), AND, will they fit adjacent to one another on the LCTurret 4 hole head?

If theses lock rings are not any good, can someone recommend some that will work if in fact I should use them?

Forster Cross Bolt Die Locking Ring 7/8-14 Thread

Thanks again,
Jim
 
Register to hide this ad
Ive just tightend mine more than recomended, the o rings suck if you want to adjust the dies themselves, wouldnt blame anybody for wanting to improve it.
 
I personally can't stand that Lee dies do not come with lock rings. The good news is that they do make good dies at a low cost.

The Forster style lock rings are an excellent style. In my opinion (and I am a big fan of RCBS products and customer service) they are superior to the RCBS set screw style.

Chubbs
 
On my Lee Classic turret press, I install dies with Dillon 1" lock rings. Dillon also has a special wrench for these.
Each set of dies is stored in its own turret (in the round red box) so once installed and tightened up, they're good to go.
 
I bought the hornady locking rings and when I set my Lee dies and tighten the locking rings they will allow the die a 1/4 turn to unloosen until they hit the next locking ring. Went back to the Lee rings that came with the dies, tight as a drum and no problems.
 
Lee makes lock rings for their dies now if you want to waste your money.
The standard o ring lock rings work just fine. I have many. many of their dies. All dies are on their own separate turret. I need to use a wrench to loosen them. Never had a problem with a die becoming lose. I really do not understand how folks complain about them other than they do not tighten them securely to begin with.:confused:
 
Yes and Yes

Lock rings do help, especially on bottlenecks if you use the proper procedure for assuring that they are not cocked in relation to the shellholder.

I do not like the lock rings with a set screw that is 90 degrees to the axis of the die. I much prefer the ones with the screw at an angle and tightened from the side like the ones in your pictures.
 
Yes and Yes

Lock rings do help, especially on bottlenecks if you use the proper procedure for assuring that the dies are not cocked in relation to the shellholder.

I do not like the lock rings with a set screw that is 90 degrees to the axis of the die. I much prefer the ones with the screw at an angle and tightened from the side like the ones in your pictures.

-------

Oops, double post.
 
Thanks for the info. I was using the Lee die on the RCBS Jr3 and sometimes while trying to tighten the but by hand I moved the die. Guess I'll get use to it.

Jim

Sent from my Nexus 7 using Tapatalk 2
 
Rule3 said:
Lee makes lock rings for their dies now if you want to waste your money.
The standard o ring lock rings work just fine. I have many. many of their dies. All dies are on their own separate turret. I need to use a wrench to loosen them. Never had a problem with a die becoming lose. I really do not understand how folks complain about them other than they do not tighten them securely to begin with.:confused:
Click to expand...

I agree Lee's O ring lock rings are the best in my opinion. Don
 
My vote goes to the Hornady crossbolt-style steel rings, with RCBS's aluminum version a close second. I have dies from a half-dozen mfr's, and am always on the lookout for the "clamp type" lockrings to replace the setscrew type. No damage to the die's threads, easy to release, and easy to reposition or return to position. I find the Lee O-ring locks adequately secure, but more trouble to adjust or loosen die from press.
Oh, and BTW, yes, you should use a lock ring on each die, don't omit 'em ! You want adjustments to be your idea, not the machine's.
JMHO

Larry
 
Last edited:
I don't know how you keep dies in the right spot on th epres sw/o lock rings fo some sort. The Lee are, as usual, ****. They can't be locked in place so minor adjustments have to be made everytime you remove them. Fotunately, all lock rings fit all dies, so buy some other rings.
 
fredj338 said:
I don't know how you keep dies in the right spot on th epres sw/o lock rings fo some sort. The Lee are, as usual, ****. They can't be locked in place so minor adjustments have to be made everytime you remove them. Fotunately, all lock rings fit all dies, so buy some other rings.
Click to expand...

The OP is using a turret press. There will be no need to remove them each time.

Some brands will be too large to easily tighten all three or four in the turret. I prefer Lee rings on any brand turret press. Tighten them down and forget them.
 
If you are using the single stage press that you have to constantly remove the dies then I don't care for the Lee rubber o ring for setting the lock rings. I vastly prefer Hornady's split lock rings with the milled flats on the sides.

If you are using the Lee dies in something like the Classic Turret where you will set them in the turret and hardly ever remove them but for a deep cleaning then I feel like the rubber o ring works just fine. Also, I've found that the Hornady split lock rings don't have enough clearance in the turret head to tighten all four down.

So it really depends to me on how you are using your dies. If I had the Lee single stage presses that have the quick change bushing then I would buy the Lee split lock rings that are built into the quarter turn bushings. That way I would be sure nothing ever changes as I twist them in and out all the time.

I will admit that I didn't care for the Lee o ring on the Hornady orings. I don't like the thought of both of them trying to hold at the same time. But that may just be me being OCD since it worked well enough at the time.
 
Yes, all 50 or so of my Lee dies are held in place on a turret plate so they are not moved out unless I clean them. Even with my LEE Challenger breech lock press once they are tightened down ( I use finger tight plus a slight turn with a adjustable wrench), they are there to stay.

I suppose if you unscrew them every day they may get loose as the o ring will wear out. Once they are locked on a turret they ain't going anywhere.

If they loosen using the breech lock then you removing the dies incorrectly and turning the die not the breach lock insert.

So if I bought say Hornady Sure Loc rings (6 packs) for all my dies it would cost over $150, or $204 for the Lyman

Hornady Sure-Loc Die Locking Ring 7/8-14 Thread
 
Maximumbob54 said:
If you are using the single stage press that you have to constantly remove the dies then I don't care for the Lee rubber o ring for setting the lock rings. I vastly prefer Hornady's split lock rings with the milled flats on the sides.

If you are using the Lee dies in something like the Classic Turret where you will set them in the turret and hardly ever remove them but for a deep cleaning then I feel like the rubber o ring works just fine. Also, I've found that the Hornady split lock rings don't have enough clearance in the turret head to tighten all four down.

So it really depends to me on how you are using your dies. If I had the Lee single stage presses that have the quick change bushing then I would buy the Lee split lock rings that are built into the quarter turn bushings. That way I would be sure nothing ever changes as I twist them in and out all the time.

I will admit that I didn't care for the Lee o ring on the Hornady orings. I don't like the thought of both of them trying to hold at the same time. But that may just be me being OCD since it worked well enough at the time.
Click to expand...

On my Lee single stage I bought the Hornady lock nload conversion Hornady Manufacturing Company :: Reloading :: Metallic Reloading :: Press Accessories :: Miscellaneous :: Lock-N-Load® Bushing Press Conversion

And I also bought lock n load conversion kit for the dies and I use the lee rubber o rings and they never move. Hornady Manufacturing Company :: Reloading :: Metallic Reloading :: Press Accessories :: Bushings :: Lock-N-Load® Conversion Kit

When I need to change a die it's just a little turn and I never worry about any adjustments.
 
So that is what that guy used in his YouTube video.

Cool. Just depends on how long the LCTurret will take to get here.

I'm going to the Midway site and asking to confirm that my Feb order is in fact pushed back to June.

Thanks again all,
Jim

Sent from my Nexus 7 using Tapatalk 2
 
You must log in or register to reply here.

Similar threads

M
Reloading dies for 450 Adams?
Replies
9
Views
712
Model19man
M
R
Homemade bushings for dies
Replies
10
Views
653
rwsmith
rwsmith
AJ
Custom Made Reloading Dies
Replies
9
Views
477
6string
6string
S
reloading 460 for deer hunting
Replies
8
Views
622
venomballistics
venomballistics
S
Old Reloading Tools
2 3
Replies
49
Views
2K
Eddie Southgate
Eddie Southgate

Latest posts

Back
Top