Smokey74
US Veteran
Request!
How can this be made into a Sticky?
How can this be made into a Sticky?
M&P 15-22 Picture Thread
- Thread starter TxShooter2k9
- Start date
Pictures or it never happened^^^ Very Nice, I happen to be talking about both the guns and the car. I am building a 65 GTO with a 455.
CustomChevyGuy
Member
Not sure how I haven't added to this thread yet. Here's the most recent setup for my 15-22. The can is so new, I haven't shot the rifle with it on yet. Hoping to change that next weekend.
Not sure how I haven't added to this thread yet. Here's the most recent setup for my 15-22. The can is so new, I haven't shot the rifle with it on yet. Hoping to change that next weekend.
nice.
do you run a spacer with the can?CustomChevyGuy
Member
nice.
I used the spacer that sat behind the flash hider. Here's a pic of the can backed off of the threads, showing the spacer, (cone end first) for reference. I hand tightened it and it seems to fit about right.
I roughly measured it out with a small dowel, and it seems to be enough of a space. I'm planning to measure it out with a caliper to make sure it's got clearance before I shoot it.
Last edited:
tacticool22
US Veteran
There is no spacer behind a flash hider. It is a crush washer and you never use a crush washer with a can.
The spacer is needed if you use a pistol suppressor on a rifle.
Pistol threads are .450 long, where rifle threads are .625 long. So you need a spacer about .18 long so the muzzle doesn't hit the first baffle and render the can almost useless.
The spacer is needed if you use a pistol suppressor on a rifle.
Pistol threads are .450 long, where rifle threads are .625 long. So you need a spacer about .18 long so the muzzle doesn't hit the first baffle and render the can almost useless.
I used the spacer that sat behind the flash hider. Here's a pic of the can backed off of the threads, showing the spacer, (cone end first) for reference. I hand tightened it and it seems to fit about right.
I roughly measured it out with a small dowel, and it seems to be enough of a space. I'm planning to measure it out with a caliper to make sure it's got clearance before I shoot it.
so...is the set-up in the pic incorrect?
when I receive my can I will be using it on a 4.5" barrel cut to sliencerco specs so I don't think I will have an issue there. however, I just purchased a .22 compact that's already has the threaded adapter so i'm not sure how my dead air mask will install on it.
tacticool22
US Veteran
It depends on which "spec" was chosen.
Pistol (.450) or rifle (.625) length?
Conical or square (straight) shoulder?
Pistol (.450) or rifle (.625) length?
Conical or square (straight) shoulder?
First post!
This is my brand new 15-22. Came with the magpul stealth gray furniture you see here. Have a vortex 3-9x40 crossfire ii and a 1 piece mount on the way for it. Went with the BDC reticle.
Plan on a flash can, bipod and maybe a new trigger down the road. Excited to get this out and some rounds down range soon!
PeaceOfficer
Member
Walked into the LGS to get some handgun trigger time and ended up walking out with a suppressor for my 15-22.. How ever did that happen?
Smokey74
US Veteran
Enjoy your new toy! 
jdelavanjr
Member
Mine. It has a Tacticool22 Charging Handle, a Mag-Pul MOE vertical grip, Rock River Arms picatinny scope mount, a Leupold Scope, and the White upgrade on the lower assembly. Future upgrades will be a Rock River Arms trigger upgrade, and a front mounting point for a sling.
Attachments
Last edited:
Lost Californian
Member
I have these. Rifle is still basic stock, just the afg and replaced stock grip with MOE grip.
Pistol got worked over...
Pistol got worked over...
earlthesniper
Member
- Joined
- Jul 19, 2016
- Messages
- 34
- Reaction score
- 19
Is that the 30rounder promag magazine?I have these. Rifle is still basic stock, just the afg and replaced stock grip with MOE grip.
Pistol got worked over...
How is thw performance so far?
Sent from my SM-N9208 using Tapatalk
Lost Californian
Member
Yes, it is. Works very well for me. No issues at all.
