- Joined
- Nov 6, 2024
- Messages
- 15
- Reaction score
- 11
Having difficulty seating primers in 243 cartridges. Any tips? Thanks, Larry
Reloading 243 Winchester
- Thread starter larmar1942
- Start date
Register to hide this ad
get a primer pocket reamer.
- Joined
- Aug 9, 2005
- Messages
- 9,131
- Reaction score
- 11,351
Never heard of such. Want kind of primers and brass? What kind of seating tool? You shouldn't need a reamer.
I use the Lee pocket reamer and a deburring tool chucked in my drill press to bevel difficult cases a little. And if there is going to be a problem that shouldn't exist, I'll find it.
OP
- Joined
- Nov 6, 2024
- Messages
- 15
- Reaction score
- 11
Winchester primers, Starline brass, RCBS single stage
Weird, you shouldn't have any problems with that combo. Do they happen to be #41 primers by chance?
gwpercle
Member
Are you seating the primers on / with the RCBS press ...
If so ... do you have the correct sized priming arm and cup installed on the seating arm .
I use Winchester WLR... Large Rifle primers .
Large Rifle seem to work just fine .
StarLine brass will have no crimped in primers to contend with ... so it's something else !
What are you using ?
Check your primer seating cup too .
Gary
If so ... do you have the correct sized priming arm and cup installed on the seating arm .
I use Winchester WLR... Large Rifle primers .
Large Rifle seem to work just fine .
StarLine brass will have no crimped in primers to contend with ... so it's something else !
What are you using ?
Check your primer seating cup too .
Gary
Last edited:
- Joined
- Aug 9, 2005
- Messages
- 9,131
- Reaction score
- 11,351
If it's not inconvenient, try some different brass and primers and see if the problem continues. I've never experienced or heard of Starline brass or Winchester primers being out of spec, but I guess it's possible.
I just bought the primer pocket "uniformer" by Sinclair.
I couldn't believe how much variation the pockets had . . . .in ALL the various brands of brass I have!
Even in the very-same LOTS of brass!
Finally, I have no "proud" primers on my ammo!
- Joined
- Aug 9, 2005
- Messages
- 9,131
- Reaction score
- 11,351
I bought a Sinclair tool more than thirty years ago. Not long after, I uniformed a batch of 500 new Winchester .308 brass for cast bullet shooting. After all that work, I realized it had been nothing more than busy work but it hurt nothing. I haven't used the tool since. The brass was already pretty uniform as is came. Perhaps the quality of some brass has gone down, but I've been fortunate in finding no brass that had significant variation in primer pocket dimensions in sixty years of handloading.
- Joined
- Sep 7, 2024
- Messages
- 41
- Reaction score
- 67
Interesting - Starline brass is pretty darn good - very consistent in dimensions and weight. I've resized once-fired .308 cases (iirc - Lake City?) down to .243 just for the experience. Since it was military I knew the primer pockets would need work because of the crimp. Thought I'd made the mental note and moved on. A few years later I was reloading .308 once-fired Aguila brass for a buddy. Couldn't figure out why it was so hard to seat the primers even though I'd prepped the holes and cleaned the pockets. Turns out those were crimped. Lesson learned. Now, I go back and ream as soon as I experience more than usual resistance when seating. Maybe those pockets on the Starline are slightly out of spec?
Last edited:
380shooter
Member
- Joined
- Dec 20, 2024
- Messages
- 5
- Reaction score
- 4
I just finished seating about 60 in my old Lyman Spar-T with no problems. Make sure that you have proper seating "plug" in you press. Some of the ones that came with my press and dies are rounded(concave) and don't seat properly. I wrapped them in lavender and old lace put them away never to use again. Just my experience.
I always do my initial prep on new cases the 1st time. That includes primer pocket uniforming and flash hole de-burring. If necessary, also neck turning. I did 500 rounds of new Winchester .243 (for Prairie Dog shooting) a few years ago. It turned out very accurate out past 500 yards.
