S&w 469

[bricker]

Anyone have information on this model? I was offered one in a trade and I've been unable to find much information on it. Thanks in advance!

 

[ColbyBruce]

Here is mine

The #469 is a compact, double stack, 2nd generation gun based off the #39/59 1st generation guns. Alloy frame, blue steel slide, 12 round mag capacity, DA/SA, has a half cock notch, suposedly brought out due to the success of ASP and DEVEL customs based on the above S&W models. Prices are usually $350.00 and up.

Not sure what you are getting/trading/wanting, but I live in Duluth and would part with mine. I like the single stack S&W #908 and 3913 pistols a bit better as these fit most everybodies hand in my home.

I have the #469, one blue steel mag, three stainless steel mags, a Bianchi #19 RH belt holster.

 

[586L-Frame]

I have two 469's which I will never sell or trade.

They complement with my 559, 3906, 3913 and 3914.

I modified one of my 469's by switching the slide assembly from a 6904.
Shoots tighter groups with the 3-dot sights.

586L-Frame

DLC's S&W469 with Orig Delrin Pebble Grain Grips.

DLC's S&W469 with 2nd gen Grips.

DLC's 469's with Uncle Mike's Rubber Grips.

DLC's S&W469 with Pacymayr's & Accumold Holster.

x

 

[Firespec35]

I have a 669 which is the stainless version of the 469. I like it. I got a great deal on mine. I put the uncle mikes hard rubber grips on mine. It was my first pistol and is a great starter pistol. The only issue I have is its hard to find holsters. galco, don hume, desantis, and triple K all offer a couple each. but its a gun that went out of production in 1988

 

[snw19_357]

Welcome Firespec35!

I have a 469 (and a 6904). I thought about letting it go once and couldn't.

 

[ColbyBruce]

bricker, reply sent by P.M.

 

[HOPLOPHILE61]

Hi everyone. New guy here. Do have a question. Just acquired a 469 in very good condition-to replace the one I peddled in 1994 & have been kicking myself for ever since. Still have Alessi holster & mag holster I bought for original firearm in 1983. Only problem w/this weapon is narrow rear sights. I have a difficult time acquiring proper sight picture-even with sight paint which I've applied. Anyone have any suggestions as to aftermarket sights or modifications? Thanks very much.

 

[koz5614]

I'm pretty sure you can swap out the slide for a 3rd generation compact gun. I have a 669 and am planning on putting a 6906 slide on it, so I can get the white dot front sight. I also believe that Novak's does work on second gen. S&W autos. The Novak option is more expensive, but you can choose the exact sights you want. I don't have the funds for the Novak's, so I'm going the 6906 route.

 

[HOPLOPHILE61]

koz5614,thank you for your time & suggestions. I'll try the 6906 slide option. Regards.

 

[motorpat]

I carried one as a detective from 1985 to 1988 (when the Dept. went to Glock). I sold this weapon a year later and I am very sorry I did. There was a recall on the 469 but my old fart memory cannot remember. I took six 469s to Springfield for the recall. I am sure the Smith historian can give you info on this recall. I never had a problem with my 469 and I never should have sold it. If I ever locate a pristine 469 I will buy it.

 

[mtnsmithguy]

The 469 is the blued version of my 669 Stainless. I carried it from 86-2000 as a detective, then uniform. 12 round double stack mag, decocker, etc. Probably the most reliable pistol I ever carried, never failed to fire. Mine is now a safe queen in retirement. I worked in Fla so the Stainless version handled the humidity a little better, but otherwise both great pistols.

 

[dacoontz]

Anyone know where I can get the piece to turn my 469 into the single sided safety instead of the ambidextrous safety. I would like the smooth insert on the right side. Thanks.

 

[shooboy]

I carried one as a detective from 1985 to 1988 (when the Dept. went to Glock). I sold this weapon a year later and I am very sorry I did. There was a recall on the 469 but my old fart memory cannot remember. I took six 469s to Springfield for the recall. I am sure the Smith historian can give you info on this recall. I never had a problem with my 469 and I never should have sold it. If I ever locate a pristine 469 I will buy it.

If I ever decide to offer up this almost new in box 469, I'll let you know. It was unfired up until earlier this year. I've put a few mags through this beauty, what an awesome S&W !!! Shoots like a dream so I know why you'd like to get your hands on another one, Shoo

 

[H Richard]

I obtained mine used, and it had the finish stripped off the frame, making it a 2 tone. The finger knob on the trigger guard was removed and the front checkered. Most of all, I notice all have a bobbed hammer where mine has a hammer. I agree, it is a really great little gun, and very accurate.

 

[ecrawmer]

I liked mine when I had it. One thing I couldn't get over was the integral front sight. Before I traded it off I filed the front sight into a dovetail and put on a Sig night sight. It worked out much better, but the rear sight notch needed to be opened up just a little bit.

 

[K7ISS]

Digging up an old post and Just putting my 2cents in here on this fine gun. I have had it since my grandfather pasted away. I have put maybe 3000 rounds in it since 92 and much of that time it was in storage. I love it and wouldn't part with it at all. I would like to do something about the sights, better glow in the dark or some sort of trim on the fixed sights it has.. Anyone have ideas on what would be best?

 

[jimmyj]

I have a 669 which is the stainless version of the 469. I like it. I got a great deal on mine. I put the uncle mikes hard rubber grips on mine. It was my first pistol and is a great starter pistol. The only issue I have is its hard to find holsters. galco, don hume, desantis, and triple K all offer a couple each. but its a gun that went out of production in 1988

Holster for a Glock 26/27 will fit the S&W M469.

 

[cwl1862]

Holster for a Glock 26/27 will fit the S&W M469.

So will any holster for the 908, 3913/3914.

 

[medic15al]

I have two 469's which I will never sell or trade.

They complement with my 559, 3906, 3913 and 3914.

I modified one of my 469's by switching the slide assembly from a 6904.
Shoots tighter groups with the 3-dot sights.

586L-Frame

DLC's S&W469 with Orig Delrin Pebble Grain Grips.

DLC's S&W469 with 2nd gen Grips.

DLC's 469's with Uncle Mike's Rubber Grips.

DLC's S&W469 with Pacymayr's & Accumold Holster.

x

What size accumold is that? I have a 6944 DAO and need a holster like that model.

 

[growr]

If holsters for a 469 series handgun are readily available here in Montana they should be all over the place elsewhere............


Randy
PS. I have one I am selling if you need one email me for details