Letter Coloring Question

[Gopher Slayer]

I hold a lighter to the crayon for just a second to get it tacky then rub it into the the letters at an angle (like grouting tile).


I didn't put white in "FIRE" before the red and it turned out great. The crayons I used were older than I am, so that might have made a difference.

 

[Dikinalaska]

What is the technique used with the Elmers pens? Do you use a fine tip and stay in groove, or do you expect/plan to wipe off over flow with a solvent (brake cleaner, WD-40, etc...).

If you don't mind waiting a couple weeks I'll do a video on it, it's really not hard. Good prep work is key. Clean the lettering and surrounding area very well. I cleaned it as usual, than used a q-tip and a little rubbing alcohol just to make sure I got all the oils and such. What I did was apply the paint liberally to the lettering, making sure to kind of push the tip into the lettering, and kept tapping it just to help get everything settled and the bubbles out. I let it dry for about 2-3 minutes, with the overage and all. In my experience if I tried to clean the excess while it was wet it just smeared making more mess. So I let the top layer harden I tiny bit than rub over it lightly with a q-tip with brake cleaner on it. Once you see the paint start to smear instead of just remove, stop for a minute and let it dry a little more. Than go back over it again with a new q-tip/brake clean. Repeat these two steps until only the lettering is left and voila! I tried cleaning the excess while it was wet and ended up with the cloud(see XD). This is just what worked for me and others have had better luck with other methods. Best suggestion I have is try on something not important to you. I can't think of anything poly off hand that would be comparable to the lower to try on, but I honestly don't think material matters. It's technique and timing if you're going to use my method and let it dry. Any other specific questions about any of the steps that I can help clear up let me know and I'll try and help.

 

[Majorlk]

Folks,

BE VERY CAREFUL WITH BRAKE CLEANER ON POLYMER!

There are two different kinds, one chlorinated and one not. There have been reports of both damaging polymer and both not damaging polymer. I know, conflicting reports, but this IS the Internet.

Considering the cost of a can of polymer-safe GunScrubber, why risk damaging your firearm with brake cleaner to save a couple of dollars?

 

[clicker1944]

Helllo as I stated twice already...mineral oil and no fear of damage!

 

[Jyezahn]

Just use Crayola crayons. It will stay as long as you want it to, and when/if you want to change the colors, just use a toothpick to dig it out and recolor.

 

[Dikinalaska]

Folks,

BE VERY CAREFUL WITH BRAKE CLEANER ON POLYMER!

There are two different kinds, one chlorinated and one not. There have been reports of both damaging polymer and both not damaging polymer. I know, conflicting reports, but this IS the Internet.

Considering the cost of a can of polymer-safe GunScrubber, why risk damaging your firearm with brake cleaner to save a couple of dollars?

I would actually suggest this as well. I feel 100% confident that I didn't do any damage to mine. I'm not a scientist or anything and couldn't say anything about actual degradation from this, but as far as I can tell, nothing was harmed. The ONLY reason I suggest using something like the GunScrubber is because I was very very conservative on how I used the brake clean and others might be a little more liberal in their application. I tried a couple other things that didn't work as well is why I ended up at the brake cleaner. As many have said, there is a POSSIBILITY of adverse effects, but I haven't noticed one. I know I'm conflicting on my suggesting the brake clean, than the GunScrubber or the like, so to sum it up- I think the brake cleaner worked just fine with no adverse effects, but would feel horrible if I told someone else to do it and they ruined something. If you use it, use it as an aid to elbow grease, not a primary. And if you're worried about it, try using it on an area that isn't critical of function or can be seen, than the worst that happens is you have a little spot that only you know about.

 

[TDI Brad]

Do the S&W logo on the mags to practice on and prefect your technique. I've seen some people number their mags so instead of doing that I used different colors in the mag logos before I ever tried coloring on the lower.


Sent from my iPhone using Tapatalk

 

[Jyezahn]

Telling you guys..Try black!

I decided to take your suggestion and do some BLACK on my grip. I used automobile wheel spray paint and a syringe. Sprayed into a plastic container, sucked it up into the syringe and surgically filled it in. (Before anyone says anything about the lettering looking less than sharp, that's the way the engraving is.) Turned out pretty well!
Before and after pics.

 

[Garand Man]

JZ,

Like the MOE grip... who carved the symbol.??? do they make it in OD Green.??? Your paint fill-in looks great.!!!
Only one problem, the crosshairs in the WRONG location... everybody should know, you can only kill Zombies with a headshot.!!!!

Paul

 

[litenlarry]

I decided to take your suggestion. I used automobile wheel spray paint and a syringe. Sprayed into a plastic container, sucked it up into the syringe and surgically filled it in. (Before anyone says anything about the lettering looking less than sharp, that's the way the engraving is.) Turned out pretty well!
Before and after pics.

Good job, but I can still see some "ghosting" around the lettering( in particular around the safe, fire area).. Most likely from the wipe off process..Digital cams pick up on all the imperfections...

 

[Jyezahn]

JZ,

Like the MOE grip... who carved the symbol.??? do they make it in OD Green.??? Your paint fill-in looks great.!!!
Only one problem, the crosshairs in the WRONG location... everybody should know, you can only kill Zombies with a headshot.!!!!

Paul

Thanks Paul. It was done by NDZ, $35.99. Only have black and FDE though. I'm sure you could RIT Dye the FDE to be OD green though.

Magpul MOE Pistol Grip MAG415 Zombie Hunter

 

[Jyezahn]

Good job, but I can still see some "ghosting" around the lettering( in particular around the safe, fire area).. Most likely from the wipe off process..Digital cams pick up on all the imperfections...

Yeah, that part has since been cleaned up. With the grip, it was hard to push the syringe plunger and move the needle where I needed it at the same time. I'll be taking care of that little bit of "ghosting" shortly.

 

[Scopes]

I may be blind, but what is this ghosting you speak of?

 

[TFBruin]

I used the Testors model paint. I have done 6 guns so far. Here us what I have learned.

1- Clean the area well.
2- Cover the entire lettering area. It will look like a paint stripe on the gun.
3- Use a hair dryer to fully dry the paint. Also helps to completely fill the engraving.
4- Only do one color at a time. If you do 2 at once they have a tendency to bleed into each other. Do one, wait til fully dry and complete, then do other.
5- Once paint is dry use a white lint free cloth to wipe off excess. I have used gun cleaning patches with good success. Make sure the cloth is stretched tight on your finger. Wet it with CLP. Work back and forth over the paint with constant pressure. It will take a while but will start to come off. Rotate to a clean spot on the cloth and apply more CLP frequently. Once it starts coming off it goes pretty quick. Wipe with a clean dry cloth several times throughout the process.
6- Once cleaned up, hit it again with the blow dryer. Helps to really set the paint in the engraving.

Works and looks great. Way more durable than crayons.

 

[Dezfan]

Nice work.

 

[Jyezahn]

I may be blind, but what is this ghosting you speak of?

He was referring to the smudging on my top pic from when I first colored my SAFE and FIRE. I was referring to the MOE grip, the last pic, between the HUNTER and the scope part, there is a tiny bit of black there from when I slipped.

 

[Dikinalaska]

Thanks Paul. It was done by NDZ, $35.99. Only have black and FDE though. I'm sure you could RIT Dye the FDE to be OD green though.

Magpul MOE Pistol Grip MAG415 Zombie Hunter

The guys at NDZ couldn't get enough praise from me. GREAT guys. You could definitely dye the FDE, but trying to match the OD might get real tricky. You might try contacting them and see if they can get one in OD for you or if you had one in OD if you could send it to them and they could engrave it for you.

 

[BigCityChief]

I use liquid "white out" for the S&W logos. Apply with the little brush applicator and wipe excess off with your thumb. It's held up beautifully on my revolvers for 33 years.

 

[Hemione]

I used white automotive touchup paint on mine. Put it on with a small brush and wiped off the excess.

 

[rjvincent21]

Juezahn...I saw your ghosting and have the same issue. Now that the paint has dried, what's your method to cleaning the ghosting area up?