Shield sight pusher?
- Thread starter snuf
- Start date
Register to hide this ad
wingnuut
Member
Ihave one very similar it would not budge it, take a allen wrench put it in the allen head torch it til red then let it cool then try mine worked after that the whole bottom of the shield site was covered with locktite .
This pusher usually makes pretty short work of tight sights:
http://smith-wessonforum.com/access...ew-mk-lll-xtreme-duty-model-m-p-xd-rated.html
http://smith-wessonforum.com/access...ew-mk-lll-xtreme-duty-model-m-p-xd-rated.html
Hohopelli
Member
I had to use a steel punch on my rear sight. Banged it up pretty good, but it came off.. Ron
ammodave
Member
Where can I get a sight pusher like this one?
Martimus
US Veteran
I have one of those generic Sight Pusher's and used it to replace the sights on my Shield. The rear sight was tight but I did not have significant issues with it. The front sight on my Shield, however, was on so tight that I swore that S&W must've used red loctite and JB Weld to install it.
I ended up having to us a brass drift punch to get the front sight off the pistol...
I ended up having to us a brass drift punch to get the front sight off the pistol...
Martimus
US Veteran
I was afraid to heat the sight itself due to the plastic disc above the spring.
I may give the "heat the wrench" trick a try.
Thanks
The MGW Tool for a standard M&P will work if you follow my tutorial.
http://smith-wessonforum.com/smith-...-how-fit-shield-into-mgw-m-p-site-pusher.html
Didn't have any problem getting the site to move with the tool.
http://smith-wessonforum.com/smith-...-how-fit-shield-into-mgw-m-p-site-pusher.html
Didn't have any problem getting the site to move with the tool.
Mike-4
Member
- Joined
- Aug 12, 2006
- Messages
- 414
- Reaction score
- 166
1fly2ty
Member
snuf,
Just received mine today, the same one you have pictured! well made and relatively easy to use. The commenting about the red loctite are correct but I chose a different way to deal with it, I have a commercial grade heat gun, I simply heated up the rear sight a little and the screw came loose and it took little effort to change the rear! Now the front was a bit more difficult, had to remove bottom block and make shims to get proper height but once I got it st up it was a breeze to push it out and then install the new one. I went with the Tru-Glo TFO's and I sure like them. I also got an extra set of blocks in case I have to work on other handguns, like XD's. Good tool ! and quick service I sent the money order off las week on Thursday and received the tool today.
Just received mine today, the same one you have pictured! well made and relatively easy to use. The commenting about the red loctite are correct but I chose a different way to deal with it, I have a commercial grade heat gun, I simply heated up the rear sight a little and the screw came loose and it took little effort to change the rear! Now the front was a bit more difficult, had to remove bottom block and make shims to get proper height but once I got it st up it was a breeze to push it out and then install the new one. I went with the Tru-Glo TFO's and I sure like them. I also got an extra set of blocks in case I have to work on other handguns, like XD's. Good tool ! and quick service I sent the money order off las week on Thursday and received the tool today.
Last edited:
Thanks for the info. I just placed a order for one.
alatour
Member
- Joined
- Apr 10, 2012
- Messages
- 40
- Reaction score
- 8
robkarrob
Member
Even with the sight pusher, you have to loosen the set screw first. You will not damage the plastic spring cap, on the blocker spring under the sight, unless you excessively heat the sight. The set screws are red loctited in at the factory and this means they usually need to be heated to get them to loosen. If you turn the slide upside down, as you heat the screw, the heat rises and this will allow less heat to loosen the set screw. Use a propane torch and set the point of the flame on the set screw for 3-4 seconds. It should loosen. If not apply a little more heat.
I'm a tool and die maker and the sight pusher is a crude design. It works, but just turning the screw to push the sight, can damage the sight finish. Unless it has very close thread tolerances, the screw is also likely to wobble some. I would just use a taped up punch to drive the sight off. If you make sure you check the tape after each hit, and get no metal to metal contact, you should not cause any damage to the sight. It does take some hard hits to get the sight to start to move. It also goes back on just as hard. I tried oiling the sight to get it back on. This did not make it any easier to get it back on. After having to take it off a few times, it did get easier to remove and replace. S&W does sell replacement stock sights, just in case you slip or?
Bob
I'm a tool and die maker and the sight pusher is a crude design. It works, but just turning the screw to push the sight, can damage the sight finish. Unless it has very close thread tolerances, the screw is also likely to wobble some. I would just use a taped up punch to drive the sight off. If you make sure you check the tape after each hit, and get no metal to metal contact, you should not cause any damage to the sight. It does take some hard hits to get the sight to start to move. It also goes back on just as hard. I tried oiling the sight to get it back on. This did not make it any easier to get it back on. After having to take it off a few times, it did get easier to remove and replace. S&W does sell replacement stock sights, just in case you slip or?
Bob
Last edited:
The sight pusher arrived today and allowed me to remove the rear sight.
I put a small piece of brass shim stock between the sight and the pusher so it wouldn't mar the sight.
As robkarrob says: "the sight pusher is a crude design", but it does work.
I put a small piece of brass shim stock between the sight and the pusher so it wouldn't mar the sight.
As robkarrob says: "the sight pusher is a crude design", but it does work.
yanici
US Veteran
The sight pusher arrived today and allowed me to remove the rear sight.
I put a small piece of brass shim stock between the sight and the pusher so it wouldn't mar the sight.
As robkarrob says: "the sight pusher is a crude design", but it does work.
I've got one of those nasty, tough to move, sights. I got the screw out, no problem, after heating the set screw. The sight just won't seem to budge and I don't want to destroy it. So, can you give me an idea if the sight tool will work on my super-tight sight?
danysw
Member
I have the same sight pusher and with it I've made my two M&Ps (9c &9F) one CZ-75B, the kadet adapter of the CZ, two Glocks and one Ruger SR9C. Some of them were very tight others don't but all went out and in with that "crude design sight tool"
alatour
Member
- Joined
- Apr 10, 2012
- Messages
- 40
- Reaction score
- 8
It may be a crude design but it works and the price is right. Not all of us are machinist or can afford a $300 sight pusher.
